Search found 76 matches

by Earl43P
Mon Apr 16, 2018 1:54 pm
Forum: GL1000 Information & Questions
Topic: please help me
Replies: 15
Views: 589

Re: please help me

Power from the start switch goes directly to the solenoid through the yellow/red wire. Ground is provided through the neutral switch or the clutch switch, through the green/red wire. There is a diode in the neutral switch circuit that if blown will only allow starting with the clutch pulled in. Ver...
by Earl43P
Mon Apr 16, 2018 12:38 pm
Forum: GL1000 Information & Questions
Topic: please help me
Replies: 15
Views: 589

Re: please help me

There are 4 wires to the solenoid, 2 small for control, 2 large for power to the starter. Start with the two large. One should have 12v applied by its direct connection to the battery. Verify that. The other large, will send power to the starter when the solenoid is activated by one of the 2 small w...
by Earl43P
Wed Mar 28, 2018 7:58 am
Forum: GL1100 Information & Questions
Topic: New 1100 owner
Replies: 6
Views: 374

Re: New 1100 owner

Hello William and welcome. Based on my own experience with an 82, I would recommend removing the heads (duh, if splitting the case). Lap the valves into their seats, replace the valve guide seals, install new timing belts, set the valve lash, clean the gas tank (I had mine done by Elizabeth Radiator...
by Earl43P
Wed Mar 28, 2018 7:32 am
Forum: For Sale/Wanted
Topic: Gl1500 parts for sale
Replies: 5
Views: 435

Re: Gl1500 parts for sale

Shocks are spoken for, see you Saturday!
by Earl43P
Fri Mar 23, 2018 10:45 am
Forum: GL1100 Information & Questions
Topic: Knocj under load
Replies: 6
Views: 356

Re: Knocj under load

The day I sold my 82 (I rode it to deliver it to the new owner after his test ride) it knocked pulling out like I had never heard it. It had also been sitting unridden for a few months. By disengaging the clutch, I quickly realized that a brake was dragging (found a hot rear rotor). I went straight ...
by Earl43P
Wed Dec 06, 2017 4:02 pm
Forum: GL1200 Information & Questions
Topic: Swop over 84 engine to 86 engine
Replies: 15
Views: 567

Re: Swop over 84 engine to 86 engine

That 84 gear indicator sensor wil swap over to the 86 engine cover if there are more wires on his original connector. But the transmission front cover has to come off to make that swap, which is a pain. Should inspect the water pump impeller for play regardless. The 84 WP may be in better shape, who...
by Earl43P
Sun Dec 03, 2017 1:58 pm
Forum: Goldwing Chat
Topic: Adventure getting my 93 SE ; The Purchase
Replies: 7
Views: 349

Re: Adventure getting my 93 SE ; The Purchase

My local dealer had side cover grommet kits for about $6.
I considered tethering mine, but it isn’t necessary with good grommets.
by Earl43P
Fri Dec 01, 2017 9:39 am
Forum: GL1200 Information & Questions
Topic: Swop over 84 engine to 86 engine
Replies: 15
Views: 567

Re: Swop over 84 engine to 86 engine

Ouch, that looks a bit like my 1100 when an intake valve snapped, took out the piston and split the cylinder wall. Only other suggestion that I have is to compare the rear covers with the thought of transplanting the vacuum advance/mag pickup/cover from the 84 onto the block of the 86. The "drive" f...
by Earl43P
Thu Nov 30, 2017 10:07 am
Forum: GL1200 Information & Questions
Topic: Swop over 84 engine to 86 engine
Replies: 15
Views: 567

Re: Swop over 84 engine to 86 engine

The freight $$ would be high, but this guy has an entire 84 engine: http://goldwingdocs.com/forum/viewtopic.php?f=9&t=40558 The reason I respond at all (having no experience with the 1200's) is that I believe your task will be daunting. The 84 spark control/vacuum advance was on the aft engine top r...
by Earl43P
Fri Sep 08, 2017 3:15 pm
Forum: GL1500 Information & Questions
Topic: Oil Leak at WP bolt and Trans cover Plug
Replies: 3
Views: 395

Re: Oil Leak at WP bolt and Trans cover Plug

Find a replacement transmission cover on eBay /Pinwall. I did mine on a jack with the front wheel removed. Disturbs coolant hoses but radiator can remain in place, drained. Seals, gasket, perhaps WP? My hoses got reconnected not replaced /shrug/. I tied hoses up out of the way. 8 mm bolts as I recal...
by Earl43P
Wed Jul 12, 2017 9:28 am
Forum: GL1500 Information & Questions
Topic: Gas coming out of tubes bottom GL1500
Replies: 6
Views: 469

Re: Gas coming out of tubes bottom GL1500

This thread should give a good idea what's involved. Good luck!

viewtopic.php?t=10504

Make sure you scroll to the last two posts in that link......
by Earl43P
Wed Jun 21, 2017 10:30 am
Forum: GL1800 (2001-2017) Information & Questions
Topic: 1800 start problems
Replies: 6
Views: 681

Re: 1800 start problems

Needs to have a good, fully charged battery @>12.5 volts; sounds like it has sat for a while. Prime the fuel system by turning key on for 2 seconds, then off. Do that at least 3 times before ever cranking the starter. Only crank the starter for short attempts, like 2 seconds max. Then re-prime, 2-3x...
by Earl43P
Wed May 10, 2017 6:54 pm
Forum: GL1500 Information & Questions
Topic: 2001 Valkyrie interstate
Replies: 2
Views: 285

Re: 2001 Valkyrie interstate

I have one of those. They like to wear out the rear drive unit pinion cup, what the tail end of the driveshaft mates to. Not visible without removing the rear wheel. Probably fine at that mileage but do grease it up asap. Inspect the inside of the saddlebags for evidence of cracks. Use a bright flas...
by Earl43P
Wed May 10, 2017 4:57 pm
Forum: GL1500 Information & Questions
Topic: Oil Leak at WP bolt and Trans cover Plug
Replies: 3
Views: 395

Oil Leak at WP bolt and Trans cover Plug

Hi fellas, need a little tech assist again. Latest wrenching adventure was the oil drain plug repair, over here http://goldwingdocs.com/forum/viewtopic.php?f=6&t=18841&start=25 Somewhat related, I've had my eye out for oil leaks after that near-catastrophe and found two forward adjacent to the Water...
by Earl43P
Mon May 01, 2017 7:44 am
Forum: Product Reviews
Topic: Insta Motorcycle Tow by BillyBob1
Replies: 55
Views: 9014

Re: Insta Motorcycle Tow by BillyBob1

I considered buying one of these front-wheel holding type trailers, back when my wife was too ill to make her monthly trips up to PA. I happened upon "this" discussion elsewhere and gave thought to simply over-filling the crankcase oil level. Instead, I modified a small trailer (which needs modified...
by Earl43P
Fri Apr 28, 2017 8:31 pm
Forum: GL1500 Information & Questions
Topic: GL1500 Stripped oil pan??
Replies: 27
Views: 1125

Re: GL1500 Stripped oil pan??

I have to say, I didn't have much confidence in your approach with the JB Weld. But, JB Weld is some pretty good stuff, and your decision to not only JB the broken parts (assuming you got those parts flawlessly clean of any residual oil), but then give them some structural support by JB Welding the...
by Earl43P
Wed Apr 26, 2017 7:04 pm
Forum: GL1500 Information & Questions
Topic: GL1500 Stripped oil pan??
Replies: 27
Views: 1125

Re: GL1500 Stripped oil pan??

Job went well, see the pictures. image32_zpshywf8wgq.jpg image23_zpsmqtf550a.jpg image13_zpsubgwfxrf.jpg I did file the sealing surface flat (not shown) and added a 1/2" o-ring that nested nicely in the timesert gap (I purposely seated it well below flush as part of my plan D revision 4). No leakage...
by Earl43P
Tue Apr 11, 2017 10:44 am
Forum: Other Bikes
Topic: VTX-1800 tech assist, won't start
Replies: 4
Views: 2641

Re: VTX-1800 tech assist, won't start

I tried calling him several times way back then and left voicemails; he never replied. Talked to a member that knows him that said he got help putting it on a trailer and took it to Honda. Months later, he sold it for a song. I never saw the bike but it had "cosmetic issues". I also completely forgo...
by Earl43P
Tue Apr 11, 2017 8:20 am
Forum: Goldwing Chat
Topic: Kool story to read
Replies: 2
Views: 1514

Re: Kool story to read

Nice story, thanks for sharing.
by Earl43P
Tue Apr 11, 2017 7:58 am
Forum: Goldwing Chat
Topic: Trip dilemma
Replies: 13
Views: 563

Re: Trip dilemma

That is an ambitious ride. I had a similar decision, NC-AZ for Thanksgiving. Really wanted to take my 82 GL1100, which I had reliably ridden many trips from NC-Pa, NC to CT, easily putting >40,000 in two years (28,500 miles per year is just my commuting). I took the 99 Valkyrie IS instead and was GL...
by Earl43P
Tue Apr 11, 2017 7:40 am
Forum: GL1500 Information & Questions
Topic: GL1500 Stripped oil pan??
Replies: 27
Views: 1125

Re: GL1500 Stripped oil pan??

You're right, that did go badly. If you go the two part epoxy route, I'd suggest JB Weld as your two part epoxy. It takes about 24 hours to cure. Don't use the JB Quick, it is not as good as the original JB Weld. Snip I'm a bit more positive in the light of day, but dwelling on it at work. I did re...
by Earl43P
Mon Apr 10, 2017 7:49 pm
Forum: GL1500 Information & Questions
Topic: GL1500 Stripped oil pan??
Replies: 27
Views: 1125

Re: GL1500 Stripped oil pan??

"...can't hardly screw it up." Oh, but I did. That went about as wrongly as humanly possible. :oops: I had to dig a bit of soil from the side of the driveway edge to get an optimum angle with the drill. No oil came out with bike laid over on its side. Used the tap guide to center the bit. Lined the...
by Earl43P
Mon Apr 10, 2017 9:04 am
Forum: GL1100 Information & Questions
Topic: 83 Aspencade - front brake hanging
Replies: 3
Views: 207

Re: 83 Aspencade - front brake hanging

"Second, what exactly is supposed to cause the caliper pistons to retract when the brake is released? Does this happen immediately that I could test it if I get the front wheel off the ground and spin it? " YES! Brake should stop the wheel from spinning, followed by immediately being able to spin it...
by Earl43P
Fri Apr 07, 2017 10:32 am
Forum: GL1500 Information & Questions
Topic: GL1500 Stripped oil pan??
Replies: 27
Views: 1125

Re: GL1500 Stripped oil pan??

Thank you for that positive feedback. Your result gives me confidence for a good result. Funny, I had already decided she was going over on her left side for this repair, solely to let the residual oil flow downhill from the drain and to raise the work up to sitting on a stool level. If I encounter ...
by Earl43P
Fri Apr 07, 2017 9:10 am
Forum: GL1500 Information & Questions
Topic: GL1500 Stripped oil pan??
Replies: 27
Views: 1125

Re: GL1500 Stripped oil pan??

You are correct in that statement, but the 4 SS inserts remaining in the kit (a half of retail price, used-once kit on E-Bay) were 28mm long and stainless. Just over an inch long (but less than my exaggeration before I did the math). Seems long so I opted for the 9.4mm which Amazon carries for a pit...