Search found 27 matches

by OTTERCOMET
Mon May 07, 2018 7:27 am
Forum: GL1100 Information & Questions
Topic: SYNCING AND IDLE SCEW ADJUSTMENT
Replies: 4
Views: 258

Re: SYNCING AND IDLE SCEW ADJUSTMENT

Thanks for the input. All the jets are the originals and when cleaning, I followed the instructions (using a bristle from a brass brush) to insure I didn't damage anything - nothing was forced. I am pretty sure I got all the passages clear - with each one, once I thought I had it clear, I'd spray so...
by OTTERCOMET
Sun May 06, 2018 10:25 pm
Forum: GL1100 Information & Questions
Topic: SYNCING AND IDLE SCEW ADJUSTMENT
Replies: 4
Views: 258

SYNCING AND IDLE SCEW ADJUSTMENT

Finally got the rebuilt carbs back in the bike and fired it up. I was amazed at how easily it started. 82 GL1100i At this point I have not synced the carbs and it appears to be idling rich and continues to be rich when revved. I am also detecting the odd backfire. 1) Will syncing the carbs reduce or...
by OTTERCOMET
Fri May 04, 2018 9:52 pm
Forum: GL1100 Information & Questions
Topic: RE-INSTALLING CARBS
Replies: 3
Views: 220

Re: RE-INSTALLING CARBS

Thanks for the input. I went with the gas tank solution - least resistance (those cross member bolts did not want to let go) - allowed me to move the tank back about 1/4" to 3/8" which was all I needed - the carbs are now in position, with slides installed - now to get the intake pipes back on the c...
by OTTERCOMET
Fri May 04, 2018 2:17 pm
Forum: GL1100 Information & Questions
Topic: RE-INSTALLING CARBS
Replies: 3
Views: 220

RE-INSTALLING CARBS

Is there a trick?? to getting the carbs back in position. I know I had a hell of a time trying to get them out and after much giggling and pulling and cursing they finally came free. I just spent an hour trying to get them back in. Float bowl of #2 seems to be hanging up on the crank case breather p...
by OTTERCOMET
Sat Apr 28, 2018 2:05 pm
Forum: GL1100 Information & Questions
Topic: GL1100 Rear Master Cylinder piston frozen
Replies: 13
Views: 1003

Re: REAR MASTER CYLINDER PISTON FROZEN

success - the grease gun worked - I even had grease appear in both the holes where the brake fluid reservoir connects - so I know both those ports are open - working on getting all the crud cleaned out of the MC before I put the new parts in. In the kit I bought the seal that goes on the piston is n...
by OTTERCOMET
Sat Apr 28, 2018 9:22 am
Forum: GL1100 Information & Questions
Topic: GL1100 Rear Master Cylinder piston frozen
Replies: 13
Views: 1003

Re: REAR MASTER CYLINDER PISTON FROZEN

In response to REDBUG's question - I hope to get back at it and try the grease gun approach today - got delayed by my 12 year old pickup - it decided to have break problems and I needed to address those first - the truck runs - the bike is a project that I hope to get running in the next couple of w...
by OTTERCOMET
Wed Apr 25, 2018 2:10 pm
Forum: GL1100 Information & Questions
Topic: GL1100 Rear Master Cylinder piston frozen
Replies: 13
Views: 1003

GL1100 Rear Master Cylinder piston frozen

Anyone had success at freeing up the piston in the rear master cylinder. I am attempting a rebuild (got the kit) and I have the brake shaft out. Unfortunately the piston and seal did not follow (as suggested in the "how to" posted in the 1100 DIY by Wingman). Have cleaned out the portion of the cyli...
by OTTERCOMET
Tue Apr 17, 2018 1:50 pm
Forum: GL1100 Information & Questions
Topic: WHERE DOES THIS PIECE GO
Replies: 5
Views: 371

Re: WHERE DOES THIS PIECE GO

Thanks for the input. Got the little piece back where it belongs.
Having access to GoldwingDocs and all the knowledgeable folks who are active on the site has been a great help - and I am likely not finished asking for help as I proceed with this project.
by OTTERCOMET
Mon Apr 16, 2018 2:03 pm
Forum: GL1100 Information & Questions
Topic: WHERE DOES THIS PIECE GO
Replies: 5
Views: 371

WHERE DOES THIS PIECE GO

DSCN0714.JPG I am doing a caliper rebuild on an 82 GL1100I. Completed the rebuild of the right front caliper and was replacing the boot on the mounting bracket, where the pivot pin goes, and this piece fell to the floor - I didn't see where it came from. I removed the left front caliper assembly an...
by OTTERCOMET
Fri Apr 06, 2018 2:19 pm
Forum: GL1100 Information & Questions
Topic: CARB SYNC USING SINGLE VACUUM GAUGE
Replies: 2
Views: 306

CARB SYNC USING SINGLE VACUUM GAUGE

I recall seeing a photo (and I think it was on this site) that depicted a setup using aquarium T connectors and shut off valves to connect the 4 carbs to a single vacuum gauge. I'm pretty sure I recall the setup but if someone has this information or can provide a link to said photo, it would be app...
by OTTERCOMET
Tue Apr 03, 2018 4:15 pm
Forum: GL1100 Information & Questions
Topic: Accelerator nozzles - carbs 1 and 2
Replies: 3
Views: 259

Re: Accelerator nozzles - carbs 1 and 2

Thanks for the responses. I originally boiled the carbs and then tried a commercial (for restaurants) degreaser, carb cleaner, brake cleaner, penetrating oil, and compressed air - managed to clear all channels in each body, except for those two accelerator jets. Subsequent to my initial post, I did ...
by OTTERCOMET
Tue Apr 03, 2018 12:35 pm
Forum: GL1100 Information & Questions
Topic: Accelerator nozzles - carbs 1 and 2
Replies: 3
Views: 259

Accelerator nozzles - carbs 1 and 2

The accelerator nozzles on carbs 3 and 4 are clear but I am having difficulty getting any spray from the nozzles on 1 and 2. Looking at 1 and 2, it appears that these jets are fed from the small fuel tubes. Am I correct that the accelerator nozzles in 1 and 2 are fed by the small fuel tubes and I am...
by OTTERCOMET
Tue Apr 03, 2018 12:23 pm
Forum: GL1100 DIY Articles
Topic: How to free up those tiny pistons on the float valves.
Replies: 0
Views: 490

How to free up those tiny pistons on the float valves.

Place the valve in a small empty container (lid off a can of WD 40 works) and put it in the freezer for 20 minutes. Boil a glass of distilled water (I used the Microwave). Drop the frozen valve into the boiling water. If it doesn't work the first time you might have to cycle through the process agai...
by OTTERCOMET
Sun Apr 01, 2018 7:57 am
Forum: GL1100 Information & Questions
Topic: FLOAT NEEDLE VALVE
Replies: 6
Views: 342

Re: FLOAT NEEDLE VALVE

pistons on all 4 valves have been freed up using the same process.
by OTTERCOMET
Sat Mar 31, 2018 10:09 am
Forum: GL1100 Information & Questions
Topic: FLOAT NEEDLE VALVE
Replies: 6
Views: 342

Re: FLOAT NEEDLE VALVE

Thanks for the input. I have managed to free up the plunger on one of the needle valves by alternately freezing and then dropping into a glass of boiling water. It is now back in the carb cleaner for some lubrication and I am proceeding with the other 3 valves to see if I can get the same science to...
by OTTERCOMET
Thu Mar 29, 2018 12:10 pm
Forum: GL1100 Information & Questions
Topic: FLOAT NEEDLE VALVE
Replies: 6
Views: 342

FLOAT NEEDLE VALVE

Rebuilding the carbs on an 82 Interstate, using Randak's kit. Got everything apart and cleaned and all channels cleared but having a problem with the needle valve plungers - can't free them up - 3 of the 4 plungers appear to be in the extended position while 1 is compressed. I have tried boiling, so...
by OTTERCOMET
Sat Mar 24, 2018 10:12 am
Forum: GL1100 Information & Questions
Topic: CV slide top limit plug
Replies: 2
Views: 246

Re: CV slide top limit plug

thanks - time to leave it alone.
by OTTERCOMET
Fri Mar 23, 2018 1:41 pm
Forum: GL1100 Information & Questions
Topic: CV slide top limit plug
Replies: 2
Views: 246

CV slide top limit plug

Rebuilding the carbs on an 82 Interstate. How critical is replacement of the O rings on these plugs. I am on my first carb #2 and while I can turn the plug in the slide, I am unable to pull the plug out of the slide and I do not want to damage the plug or the slide with excessive force. I have attem...
by OTTERCOMET
Wed Nov 22, 2017 2:59 pm
Forum: GL1100 Information & Questions
Topic: SYNC CARBS WITH SINGLE GAUGE
Replies: 1
Views: 292

SYNC CARBS WITH SINGLE GAUGE

Some time ago I read an article (I think it was on GoldwingDocs) that provided guidance on how to sync the carbs if you only had one vacuum gauge to work with. If anyone can provide a pointer to an article or possibly a URL to a web site with this info it would be appreciated. Thanks
by OTTERCOMET
Fri Aug 04, 2017 1:45 pm
Forum: GL1100 Information & Questions
Topic: TIMING BELT REPLACEMENT
Replies: 1
Views: 263

TIMING BELT REPLACEMENT

I am using the "Timing Belt Removal Replacement by Octane" to guide my effort. In the description there is a picture of a spanner zip tied to the frame. Given the way the spanner is held in place suggest that when you release the tensioner the cam pulley will roll clockwise (looking at the right cam...
by OTTERCOMET
Mon May 02, 2016 9:36 am
Forum: GL1100 Information & Questions
Topic: REMOVING CARBS
Replies: 1
Views: 263

REMOVING CARBS

I am an old guy but a rebuild rookie - so please go easy. I'm preparing to attack the carbs on an 82 GL1100I. There is a plate running in front of the carbs, that appears to be part of the upper fairing and it also appears that it might interfere with sliding the carb assembly out once it is free of...
by OTTERCOMET
Mon Dec 21, 2015 6:19 am
Forum: Tech Talk
Topic: GATES PART NUMBER FOR 82 GL1100 TIMING BELTS
Replies: 4
Views: 184

Re: GATES PART NUMBER FOR 82 GL1100 TIMING BELTS

Thanks for the direction to the reference info in Forum. I'm new to the site and so far have been spending most of my time in the How-To-Articles. Will have to spend some more time cruising around the various areas in GoldwingDocs.
by OTTERCOMET
Sat Dec 19, 2015 11:35 pm
Forum: Tech Talk
Topic: GATES PART NUMBER FOR 82 GL1100 TIMING BELTS
Replies: 4
Views: 184

GATES PART NUMBER FOR 82 GL1100 TIMING BELTS

I have been searching through posts regarding timing belt replacement for my GL1100, hoping that someone would have a reference to the correct Gates part number for these belts. Would appreciate it if someone could either provide me the information or direct me to an existing post that contains the ...
by OTTERCOMET
Tue Dec 01, 2015 10:11 am
Forum: Goldwing Chat
Topic: December Contest
Replies: 1
Views: 80

December Contest

Sure could use that $100 for my project bike.- 82 Interstate - back in 82 I really would have liked to purchase this bike but the $$$ got in the way so I settled for an 82 Suzuki GS850 that I ran for 94K km. Came upon this Interstate this past summer and couldn't pass it up. The bike was a one owner...
by OTTERCOMET
Fri Oct 09, 2015 10:42 am
Forum: GL1100 Information & Questions
Topic: 82 GL1100 INTAKE MANIFOLD GASKETS
Replies: 5
Views: 356

82 GL1100 INTAKE MANIFOLD GASKETS

I am compiling a list of parts I need to purchase when I am stateside this winter (I'm a Canadian Snow Bird). The bike I'm working on is going to need carb servicing (rebuild kits - for which I have a source lined up). My question is, do these kits include the intake manifold gasket or are these par...