How to clean/shine Chrome

Anything goes - doesn't fit any other category!
  • Sponsored Links
User avatar
Posts: 97
Joined: Wed May 16, 2012 10:11 pm
Location: Fairhope, Alabama
Motorcycle: 1998 GL1500 SE

How to clean/shine Chrome

Postby Blackngold » Sun Feb 14, 2016 8:47 am

I read something about this here but needed more detail, then I found this. I thought this was pretty cool and had never heard of this method. Just another thing to add to the TO-DO-LIST. I'm going to need another page pretty soon! Hope it works as well as it sounds. Getting some signs of pitting on tail pipes under the bags. The step by step has enough detail that maybe I won't muff it up. :lol:

Cleaning Chrome

I want my shiny fenders back. Not to worry. It's really very simple.

Rub a dub dub - A simple solution

A simple and inexpensive way to remove rust from and polish chrome surfaces by hand is to rub it with aluminum foil dipped in water. This process yields two advantages. First, since the aluminum foil is softer than steel, it will not scratch the surface. And second, a by product of the process produces a fine metal polishing compound that smoothes the chrome surface to a bright shine.

Geek Stuff - Oxides are the key

Cleaning rust is basically oxidized metal or another words metal that has taken on extra oxygen atoms. As heat is generated by the friction of rubbing the aluminum foil on the chrome, a portion of the aluminum will oxidize to produce aluminum oxide. Aluminum has a higher reduction potential (i.e a tendency take on electrons and in the process reduce or break itself down) than the chrome, and will therefore leech oxygen atoms away from any rust on the chrome surface which changes the chemical properties of the rust and breaks it down.
Polishing aluminum oxide is harder than steel, and the microscopic grains of aluminum oxide produced during the cleaning process creates a fine metal polishing compound which, mixed with the water you added, creates a paste that smoothes and polishes the chrome surface.

In English - How it works

A common way to clean a rusted chrome surface such as a fender is to use a fine steel wool. However, when you use this method you have to use a lot of elbow grease and you still end up with a slightly dull surface with some amount of scratching not to mention the messy 'dust' left over from the steel wool. That's because you are physically scraping off the rust.
When you use the aluminum foil method you are dissolving the rust chemically so you don't need to rub nearly as hard and since the aluminum foil is softer than the chrome, you are left with few if any scratches. This method also allows you to get the rust out of some minor pitting without having to dig into the surface.

The aluminum oxide that is created by friction when you rub the surface of the chrome leeches the rust away and when combined with the water you added creates it's own polishing compound so you end up with a clean, smooth, shiny surface.

Step by step - By the numbers, people

1- Cut the aluminum foil into small squares. 3" by 3" should do.
2- Wipe down or wash the surface to remove any surface dirt.

3- Dip a square into some water or sprinkle some water on it and spread it around on the surface of the foil.

4- Cup the wet square over the surface you want to clean so you get a nice even coverage.

5- Start rubbing a 6 or 8 inch area and remember you don't have to rub very hard. As you rub, you'll feel the surface get smoother and smoother until the foil just glides over it. You will also notice a light brown paste building up. This is the polish that results from the chemical reaction.

6- When the surface is nice and smooth and you have polished it, take a clean cloth and wipe the polish off.

7- Once you finish cleaning and polishing the item you need to cover the surface to protect it from the elements. At a minimum you can wipe it down thoroughly with a clean cloth. Since cloth inherently contains some amount of oil, this will give you at least some protection.
The best method would be to use a small amount of chrome polish or maybe something like turtle wax or an equivalent kind of wax or polish. Make sure you wipe the surface down with a paper towel first instead of a cloth because paper doesn't contain any oil so you will have a clean and dry surface for the wax or polish to adhere to.

Limitations - There's always a catch

If the surface is severely pitted or some of the chrome plating has peeled off, there is a limit to how much you can do. Since this method removes the rust chemically, you should still be able to get rid of most if not all of the rust. And since it creates it's own polishing compound, you should be able to feather (taper) the peeled off edges to help prevent more peeling in the future. Again, once you have the surface as rust free and smoothed down as much as possible, don't forget to apply some form of wax or polish.

Tips - Things we noticed along the way

Use a little extra water if you want a super fine finish.
Wad up a larger piece of foil when you work on pitted areas. The edges created will help smooth down the pits.

Don't rub too long with the first 'paste' created. Once the surface feels nice and smooth and you've wiped the gunk off, you can use a new piece of foil with some more water to get as much shine as you like.

Don't waste your time with a severely pitted surface since the rust has probably eaten down through the chrome to the bare metal. Smooth it down as much as you can with steel wool then use the aluminum foil method to remove as much rust as possible.

The aluminum foil method also works pretty well on steel. It removes the rust well, but don't expect that super shiny finish like you get with the chrome because it never had that to begin with.

To get the best results, remove that fender or other part so you can work on it easily without having nooks and crannies to dig into.

If you're working on severely rusted rims, you might want to use a steel brush to remove the worst rust spots first. This will also remove any caked on road gunk so you have a better surface to work with.

A final Note - Parting is such sweet sorrow...

We hope you will be as amazed with this method as we are. It has saved us a lot of time and effort and has yielded much better results than we've gotten in the past.
Have fun !

User avatar
Posts: 1298
Joined: Sun Mar 25, 2012 11:58 am
Location: Silverlake, WA
Motorcycle: 1982 Yamaha Venture (Crashed/Sold)
1982 1100 Silver Goldwing (sold)
1989 1500 Beige Goldwing (sold)
1988 1500 Beige Goldwing (current ride)

Re: How to clean/shine Chrome

Postby Mag » Sun Feb 14, 2016 11:21 am

Something to try.....hmmmm

User avatar
Site Admin
Posts: 16909
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (wife's!)
1998 XV250 Virago (sold)
2007 Aspen Sentry Trailer

Re: How to clean/shine Chrome

Postby WingAdmin » Tue Feb 16, 2016 11:17 am

I've heard of using crumpled up aluminum foil, but this is the first I've heard of using wetted aluminum foil flat. Interesting.

User avatar
Posts: 97
Joined: Wed May 16, 2012 10:11 pm
Location: Fairhope, Alabama
Motorcycle: 1998 GL1500 SE

Re: How to clean/shine Chrome

Postby Blackngold » Wed Feb 17, 2016 7:43 am

There are numerous you tube videos on procedure and results also. :D

User avatar
Posts: 2806
Joined: Thu Apr 08, 2010 8:35 am
Location: Oklahoma City
Motorcycle: 1976 gl1000
1993 gl1500
2004 NRX1800 Rune

Re: How to clean/shine Chrome

Postby dingdong » Wed Feb 17, 2016 8:08 am

When using the aluminum foil method you "must" use lots of liquid to flush the rust particles away. Foil is softer and doesn't scratch chrome but rust particles will. I read the other day that using coke as the cleaning agent works well.

A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed.

User avatar
Posts: 97
Joined: Wed May 16, 2012 10:11 pm
Location: Fairhope, Alabama
Motorcycle: 1998 GL1500 SE

Re: How to clean/shine Chrome

Postby Blackngold » Wed Feb 17, 2016 8:43 am

I read about coke also--but the disclaimer added for people with large fingers to use diet coke :lol:

Return to “Goldwing Chat”

Who is online

Users browsing this forum: No registered users and 2 guests