How to refinish aluminum covers


Step-by-step tutorials on how to maintain and fix your GL1100
  • Sponsored Links
kalekk
Posts: 9
Joined: Sun Mar 27, 2011 8:44 pm
Location: KY
Motorcycle: 1982 gl1100

How to refinish aluminum covers

Postby kalekk » Thu Apr 21, 2011 1:10 am



I paid $9.00 for a set of belt covers and $14.00 for a set of valve covers. They were in bad shape.
Ugly covers
Ugly covers
First thing to do is to clean the parts inside and out with mineral spirits , a paint brush will help clean. Next remove any clearcoat and the paint around the logo with spray auto stripper.Next use wet-o-dry sandpaper and a bowl of water to start sanding down the surface.When sanding use long strokes from end to end and follow around the curves just like you would if you were spray painting.Never sand diagonal or zigzag during any of the stages of wet sanding.I started with 320 grit because the parts were so corroded.If the parts were in better shape 400 grit could have been used.
Begin wet sanding
Begin wet sanding
You can fold or roll your sandpaper or wrap an object with the sandpaper to to get into the grooves and ribs.I used the wooden handle of my paint brush to get between the ribs and such.Sand the entire piece untill the metal is brite.If you see dark spots remaining it is from the deeper pits, keep sanding untill they are gone.The coarsest grit is going to get rid of spots faster so sand the spots away before you move on.Wipe the part clean often and look for what might have been missed.Next move to 400 grit and work the entire piece again.It should begin to look a lot better after this stage.If you find you need to rework an area or two with the coarser grade again go ahead and back up and rework those spots ,it won't slow you down much.The goal of useing a finer grit is to remove the sanding marks from the previous grit.Once all the metal looks uniform with the 400 move to 600 grit.after the 600 has been done take the part outside in the sun and look at it again.A good light sorce will help find imperfections.If you see any,fix them. At this point we might be 1 or 2 hours into the project and the part should be looking great.Next job is to polish the aluminum.If you have a diegrinder harborfreight sells a 14 pc.polishing kit for $18.00. there are other tools that polish aluminum as well,you pick.
polishing kit
polishing kit
Use a cloth wheel and the darkest polish stick first.Run the spinning wheel onto the polish stick to get the tool loaded with polishing compound then start buffing the piece with the same pattern as used earlier... long strokes end to end and folow the curves just like you would if you were spray painting the piece.Learn to not use to much pressure and not to dwell in one spot to long and when to load more polish on the wheel.A thin film of polish should be layed down.Avoid letting your buffer grab the edge of the cover and have it jerk the tool into the part or you might damage the finish.To avoid that problem make the rotation of tool tend to roll in the "onto the part" diretion rather than the "off of the part" direction.Once the part has been buffed with the darkest polish clean the part with mineral spirits and clean the buffing wheel by spinning it on a dry cloth or a piece of carpet, or switch to a fresh wheel.Work thru the grades of polish ,finish with the white polish.Clean the part again and buff it with some mothers.It should be shineing lke a new dime now.Now wipe down the part with mineral spirits let it dry then mask off the square area around the GL1100 logo and mask the entire top of the cover.Use high temp engine paint ( black ) and spray the square area, the letters and all.Wrap your finger tip with a smooth cloth and moisten the cloth with mineral spirits and while the paint is still wet carfully wipe the paint from the tops of the letters.
Painting the logo
Painting the logo
Without delay remove the masking tape from the cover and wipe the edges of the square clean to get a nice clean line around the outside.Next carefully clean the cover again but avoid the freshly painted logo.Use a tack cloth to remove any dust or lint. Use duplicolor high temp clear engine paint and seal the entire cover.Before you spray the clear coat on the part,try test painting something else first.This paint is a little tricky.I have my best luck putting down one wet coat,but not wet enough to cause a sag... rather than a light coat followed by a wet coat as I do with any other paint. For some reason It just will not lay down smooth if I use multiple coats.Go figure.Here she is hope you like.Chow
Installed
Installed
Attachments
Installed
Installed



User avatar
virgilmobile
Posts: 7644
Joined: Sun Sep 19, 2010 5:39 pm
Location: Denham Springs,La.
Motorcycle: 1988 GL1500 I
Previously owned
78 GL1000
81 GL1100
82 GL1100 I
83 GL1100 I
83 GL1100 standard
84 GL 1200 I

Re: How to refinish aluminum covers

Postby virgilmobile » Thu Apr 21, 2011 7:13 am

Mine looked the same.I started with wet 400,then wet 1000,then wet 2000,and finally Mothers Aluminum polish,all by hand.You can see yourself in them.It took 3 hours for each cover.

User avatar
dingdong
Posts: 2860
Joined: Thu Apr 08, 2010 8:35 am
Location: Oklahoma City
Motorcycle: 1976 gl1000
1993 gl1500
2004 NRX1800 Rune

Re: How to refinish aluminum covers

Postby dingdong » Thu Apr 21, 2011 8:26 am

I used basically the same method except I didn't use a clear coat. Tried clear coat on the timing covers and forks but too many rock chips and it started to yellow. Without clear coat they can be re-polished in just a few minutes every couple of months. Just my preference.
Tom

A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed.

User avatar
WingAdmin
Site Admin
Posts: 17045
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (wife's!)
1998 XV250 Virago (sold)
2007 Aspen Sentry Trailer

Re: How to refinish aluminum covers

Postby WingAdmin » Fri Apr 22, 2011 4:22 pm

It looks great! I like your method of masking and finger-wiping.

User avatar
RBGERSON
Posts: 2612
Joined: Tue Mar 09, 2010 7:57 am
Location: SCOTTSDALE, AZ
Motorcycle: 98 SE GL 1500
had every year from 75 to 83

Re: How to refinish aluminum covers

Postby RBGERSON » Sun Apr 24, 2011 8:24 am

For the lazy..I just use my grinder's wire wheel side..and it cleans them up in about 5 minutes and looks great. I f I ever get a buffing wheel I may go further and use the polish to shine them up even more. I know you can get them to look like chrome. But the wire wheel is quick and does a good job of removing all the corrosion and leaves them shining.
HAD LOTS OF GOLDWING 75-83
NOW INTO 1500'S..RIDING A 1998 SE

FAIR WINDS,
RB

goldtr6c
Posts: 147
Joined: Tue May 11, 2010 11:17 am
Location: Hitchcock, Tx
Motorcycle: 1985 GL1200 LTD
1982 GL1100 STD
1976 GL1000 "800lb Canary"

Re: How to refinish aluminum covers

Postby goldtr6c » Sun Apr 24, 2011 4:17 pm

What kind of clear coat did you use? All the ones I've used either turn dark from heat or just start flaking off.

kalekk
Posts: 9
Joined: Sun Mar 27, 2011 8:44 pm
Location: KY
Motorcycle: 1982 gl1100

Re: How to refinish aluminum covers

Postby kalekk » Mon Apr 25, 2011 9:48 am

I used duplicolor clear high temp engine enamel. I have used it for a couple of years and have not had any problems with color change, chips or peeling. Try it, I like it. If you find you don't like it for some reason stripper will take it off in a matter of minutes. I used plastikote classic laquer on a carbon fiber part once and that turned yellow within a year. Later I took that same part to a paint shop and they used polyurithane with UV additives. That turned out better than new. What product did you try that didn't work out? Talk to you later.

Woodwinger
Posts: 3
Joined: Thu Sep 08, 2011 5:37 pm
Location: VAUGHN
Motorcycle: 1963 C105
1964 CA95
1965 CT200
1966 CL77 Red Frame
1968 CL175
1969 CB750 K0
1975 GL1000
1976 GL1000
1976 GL1000 LTD #1
1976 GL1000 LTD #2
1979 CB750K LTD
1983 CB1000 Custom
2010 Honda VT750 RS
2010 Honda GL1800

Re: How to refinish aluminum covers

Postby Woodwinger » Thu May 31, 2012 11:46 pm

Has anyone ever tried finishing the polished cover with clear powder coat? It is used all the time on aluminum wheels and it is definitely heat and chip resistant. I am considering going that route on my 76 LTD when the covers come back from the polisher next month. (I know I could have done the polishing myself but the bike needs so much other stuff done I subbed that chore out).

Ken

User avatar
mytown
Posts: 156
Joined: Wed Oct 31, 2012 11:54 am
Location: Carbondale, Illinois
Motorcycle: 1982 Goldwing Interstate

Re: How to refinish aluminum covers

Postby mytown » Sat Sep 14, 2013 1:02 am

I pretty much followed the OP method and here's my results:

I first stripped the clear off with a stripper containing methyl chloride, three applications. I went 220 320 400 then 600 sandpaper, all wet. I used primarily brown and white buffing compounds. I used a green from Lowes that was for a final application but it didn't seem to do much. My final passes were made with the white from Lowes. Not perfect, as some scratches are evident,

but a noticible improvement overall.

I read how dirty the job was so I decided to do it outside, here's my setup:

Looks like heck and I made a mess of the wall of the shed, but it worked pretty well.

I worked on the covers a couple of hours at a time and would not be surprised to find out that I spent 4-6 hours or more on each one. I finished by polishing with a metal polish called MASS. The shine held up to a scrubbing at a car wash. The manager at a local body shop said that he would clear them both for $50 which I might do if the polish doesn't hold up. I considered the task as a one-time mandatory one, but I wouldn't want to do it again, same goes for the intakes and the carb tops.

User avatar
PEREZ13
Posts: 1
Joined: Wed Aug 07, 2013 6:03 pm
Location: SANTA ANA, California
Motorcycle: 1989 GL1500

Re: How to refinish aluminum covers

Postby PEREZ13 » Fri Jan 31, 2014 2:49 pm

I WAS IN NEED OF A CHROME WINSHIELD TRIM. I LOOKED ON EBAY AND FOUND THEM FOR A VERY HIGH PRICE... I WENT TO THE COSTA MESA FLEA MARKET AND SAW A MAN DEMONSTATING A "METAL GLOSS" PRODUCT. HE MADE A COMMON BEER KEG SHINE LIKE A MIRROR! AMAZED, I BOUGHT THE BOTTLE AND TOOK IT HOME TO TRY ON THE FRONT ALUMINUM ACCENT PIECE DIRECTLY BELOW THE WINDSHIELD. ONE THING HE TOLD ME THAT IF THE MICRO FIBER CLOTH DOESN'T TURN BLACK, THEN I WOULD NOT GET THE END RESULT I WAS LOOKING FOR. THE CLOTH DID NOT TURN BLACK. I WAS NOT GIVING UP! I KEPT RUBBING WITH MY SAUCE, BARE FINGERS, AND OF COURSE THE MICRO FIBER. CAPOW!!! IT STARTED TURNING BLACK! I CONTINUED AND NOW HAVE A CHROME PIECE THAT LOOKS ABSOLUTELY BEAUTIFUL. I WILL POST THE BEFORE AND AFTER PICS SOON

SidAbma
Posts: 33
Joined: Sat Feb 01, 2014 1:35 am
Location: Atascadero, CA
Motorcycle: 1985 GoldWing LE

Re: How to refinish aluminum covers

Postby SidAbma » Mon Feb 03, 2014 10:58 pm

Perez
Do you have the name of the product?
I was given a brand Autosol Polish. Hoping to find a product that is handled locally.

User avatar
chrissvitak
Posts: 19
Joined: Mon Jun 18, 2012 12:05 pm
Location: Westmont, IL
Motorcycle: 1983 GL1100 Interstate

Re: How to refinish aluminum covers

Postby chrissvitak » Sat Mar 01, 2014 10:56 am

Thanks for the info. I am going try this just to spruce up the look of the old girl. I will post a couple of pics when I get done. :D
1983 GL 1100 Interstate

Goldwing Rider for Life
OH Yah!!

User avatar
sbbeef
Posts: 2
Joined: Sat Aug 24, 2013 12:39 pm
Location: Vicksburg, Michigan
Motorcycle: 1977 GL1000

Re: How to refinish aluminum covers

Postby sbbeef » Sun Jun 01, 2014 12:36 am

Thanks for the info.
"Only two things are infinite, the universe and human stupidity, and I'm not sure about the former." "The important thing is not to stop questioning . . . Never lose a holy curiosity" Albert Einstein.

User avatar
rudolphwolven
Posts: 57
Joined: Fri Jun 20, 2014 7:05 am
Location: Netherlands - Utrecht
Motorcycle: 1975 GL1000 K1

Re: How to refinish aluminum covers

Postby rudolphwolven » Sun Aug 31, 2014 7:52 pm

Painted engine block and parts:
- 1) VHT Engine light primer...................Art.nr: SP-148 ( Spraycan 400 ml / 2 pcs.)
- 2) VHT Engine universal aluminium..........Art.nr: SP-127 ( Spraycan 400 ml / 2,5 pcs.)
- 3) AUTO-K-Spraymax 2K (2 component coating in one 2 chamber spraycan) Clearcoat high gloss (incl. conditioner)
Art.nr: 680061......( Spraycan 400ml /3 pcs.)

Polished aluminium parts:
- 3) AUTO-K-Spraymax 2K (2 component coating in 1 spraycan) Clearcoat high gloss (incl. conditioner)
Spraycan 400ml........Art.nr: 680061 { Nr. of cans included in - 3)}











picture without flashlight:


picture with flashlight:


Picture in illuminated garage:


Exhaust:
-1) VHT SP-100 Flame Proof Primer (704-1093 gr. C.) (Spraycan 400 ml / 2 pcs.)
-2) VHT SP-102 Flat Black Flameproof (Silica-Ceramic Coating / 704-1093 gr. C.) (Spraycan 400 ml / 2pcs.)



Proud winner of the NGWClub-USA contest Bike of the Year 2016--Image

bthacker
Posts: 49
Joined: Mon Oct 26, 2009 12:42 pm
Location: Afton, TN.
Motorcycle: 2005 GL1800
1977 GL1000

Re: How to refinish aluminum covers

Postby bthacker » Thu Jan 22, 2015 12:06 am

I found these at Harbor Freight and they work great. Item#95993
Attachments




Return to “GL1100 DIY Articles”




Who is online

Users browsing this forum: No registered users and 2 guests