How to register remotes to power trunk lock system


Step-by-step tutorials on how to maintain and fix your GL1800
  • Sponsored Links
Post Reply
DALIAN
Posts: 1
Joined: Mon Nov 08, 2010 5:37 am
Location: China
Motorcycle: 2002 gl1800 se

How to register remotes to power trunk lock system

Post by DALIAN » Fri Dec 03, 2010 11:56 am



NOTE:
.The turn signai lights blink twice when the trunk opener unit is unlocked using the transmitter with the ignition switch turned to
"OFF" or "LOCK"
.The turn signal lights blink once when the trunk opener unit is locked using the transmitter with the ignition switch turned to "OFF"or "LOCK."
.The horns sound twice and the turn signai lights blink twice when the "CALL" button is pushed for more than 0.5 second.
The trunk opener unit can be unlocked using the transmitter with the ignition swition switch turued to "ON" or "ACC," but the turn signal lights do not blink.
.The "POP UP and "CALL" functions do not word with the ignition switch turned to "ON" or "ACC."
.lf any of lids are open, the trunk opener unit cannot be lockend using the transmitter and the turn signal lights blink ten times when the lock button is pushed.
.If the trunk opener unit is unlocked using the transmitter but any of the lids is not opened within 30 seconds, the trunk is locked antomatically.
TRANSMITTER REGIGSTRATION
NOTE:.the codes of up three transmitters can beregisterd into the truna lock control unit memory.(if a fourth code is stored.the code which wasregistered first will be erased.)
.Make sure to keep the timing between 1 and 4 seconds for each action. Too fast or too slow will csues the control unit to lose the stored codes.
1.Turn the ignition switch to "ON." Between 1 and 4 seconds,press the trunk opener button on the transmitter while aiming transmitter at the trunk. Between 1 and 4 seconds, turn the ignition switch to "OFF."
2.Between 1 and 4 seconds, turn the ignition switch bach to "ON" Between on the transmitter whilh aiming transmitter at the trunk. Between 1 ant 4 seconds, turn the ignition switch to "OFF."
3.Between 1 and 4 seconds, turn the ignition switch back to "ON" Between 1 and 4 seconds ,press the trunk opener button on the transmitter while aiming transmitter at the trunk .Between 1 and 4 seconds, turu the ignition switch to "OFF."
4. Between 1 and 4 seconds, turn the ignition switch back to "ON." Between 1 and 4 seconds,press the trunk openr button on the transmitter at the trunk. confirm that the turn signal lignal lights blink twice.Leave the ignition switch "ON."
5.within 10 seconds,aim the transmitters (up to three) that you want to store codes in at the trunk and press the trunk opener button once on each transmitter. Confirm that the turu signal lights blink twice.Turn the ignition switch to "OFF."
6.Confirm proper operation of each transmitter with the new codes.



User avatar
AZgl1800
Posts: 266
Joined: Thu Oct 30, 2008 2:46 pm
Location: Lake Oologah Indian Territory USA
Motorcycle: '02 GL1800 still young at 111,980 miles

Re: How to register remotes to power trunk lock system

Post by AZgl1800 » Wed May 13, 2015 9:42 pm

The above is very good info, but the legibility is suffering a bit.... I took the liberty of doing some editorializing on it.


How to register remotes to power trunk lock system



.The turn signal lights blink twice when the trunk opener unit is unlocked using the transmitter with the ignition switch turned to "OFF" or "LOCK"

.The turn signal lights blink once when the trunk opener unit is locked using the transmitter with the ignition switch turned to "OFF" or "LOCK."

.The horns sound twice and the turn signal lights blink twice when the "CALL" button is pushed for more than 0.5 second.

The trunk opener unit can be unlocked using the transmitter with the ignition switch turned to "ON" or "ACC," but the turn signal lights do not blink.

.The "POP UP and "CALL" functions do not work with the ignition switch turned to "ON" or "ACC."

.lf any of lids are open, the trunk opener unit cannot be locked using the transmitter and the turn signal lights blink ten times when the lock button is pushed.

.If the trunk opener unit is unlocked using the transmitter but any of the lids is not opened within 30 seconds, the trunk is locked automatically.



TRANSMITTER REGISTRATION

NOTE:.

. The codes of up three transmitters can be registered into the trunk lock control unit memory.
(if a fourth code is stored, the code which was registered first will be erased.)

.Make sure to keep the timing between 1 and 4 seconds for each action. Too fast or too slow will causes the control unit to lose the stored codes.

1. Turn the ignition switch to "ON." Between 1 and 4 seconds, press the trunk opener button on the transmitter while aiming transmitter at the trunk. Between 1 and 4 seconds, turn the ignition switch to "OFF."

2. Between 1 and 4 seconds, turn the ignition switch back to "ON" Between on the transmitter while aiming transmitter at the trunk. Between 1 ant 4 seconds, turn the ignition switch to "OFF."

3. Between 1 and 4 seconds, turn the ignition switch back to "ON" Between 1 and 4 seconds, press the trunk opener button on the transmitter while aiming transmitter at the trunk .Between 1 and 4 seconds, turn the ignition switch to "OFF."

4. Between 1 and 4 seconds, turn the ignition switch back to "ON." Between 1 and 4 seconds, press the trunk opener button on the transmitter at the trunk. confirm that the turn signal lights blink twice. Leave the ignition switch "ON."

5. within 10 seconds, aim the transmitters (up to three) that you want to store codes in at the trunk and press the trunk opener button once on each transmitter. Confirm that the turu signal lights blink twice. Turn the ignition switch to "OFF."

6.Confirm proper operation of each transmitter with the new codes.
John
'02 Gl1800 Hot Rod Yellow,
daughter named her Big Bird :lol:
http://www.goldwingfacts.com

Post Reply