front tire sizing


Information and questions on GL1000 Goldwings (1975-1979)
  • Sponsored Links
Post Reply
gfrench5@hotmail.com
Posts: 19
Joined: Sat Nov 25, 2017 1:41 pm
Location: Ontario
Motorcycle: 1976 Honda GL1000

front tire sizing

Post by gfrench5@hotmail.com » Fri May 04, 2018 2:13 pm



Hi guys, Weather is getting nice and I'm late with new tires. Both are Shinko Classic 712. The back is OK and installed on my 1976 Sulphur Yellow Wing 130/90 by 17 but I bought a 110/90 by 19 and have not installed it yet. Should I have got the 100/90 by 19 ??? Will the 110/90 fit ?? I'd rather not pay shipping charges to return it if it is OK. What are all your thoughts??? Thanks in advance, regards Glen French.



Good Hondog
Posts: 58
Joined: Sun May 14, 2017 6:56 pm
Location: Calgary, Alberta, Canada
Motorcycle: 1980 GL1100 Interstate

Re: front tire sizing

Post by Good Hondog » Fri May 04, 2018 6:24 pm

Shinko specifications for each of those tires are:

100/90x19 has an overall diameter of 26.1 inches and an overall width of 3.98 inches
110/90x19 has an overall diameter of 26.81 inches and an overall width of 4.29 inches

Recommended rim width listed by Shinko for both those tires is exactly the same, so no discrepancy there. The load rating is a tiny bit higher for the 110/90 so that's a bonus. Basically it amounts to the front tire closing up about 3/8" of clearance under the front fender and closing up about 1/8" on either side of the tire between the sidewalls and fork legs. Your speedometer will be slightly more accurate with the 110/90x19 I would bet. I've done exactly the same change of going one size larger front tire on two of my other bikes and it's been an improvement in my opinion. One is a 1000cc and the other is a 1340cc so I'm talking big street bikes, not little lightweight motorbikes. You will have to do some measuring and make your own decisions about what is acceptable for your classic big old Goldwing. Hope this information is helpful to you.

DaveO430
Posts: 613
Joined: Fri Jan 02, 2015 7:28 pm
Location: Amity. Ar
Motorcycle: 2010 GL1800
2004 Suzuki DR200

Re: front tire sizing

Post by DaveO430 » Fri May 04, 2018 7:40 pm

On an 1100 with a 1000 front fender a 110 will fit but it is pretty close to the fender. less than 1/2" of clearance but it works.

gfrench5@hotmail.com
Posts: 19
Joined: Sat Nov 25, 2017 1:41 pm
Location: Ontario
Motorcycle: 1976 Honda GL1000

Re: front tire sizing

Post by gfrench5@hotmail.com » Fri May 04, 2018 8:16 pm

Thanks guys, especially for the specifics on tire sizing, I knew I could rely on your help with this issue it's great to have so much knowledge. I wonder how I did it in the old days. Thanks again, Glen

Good Hondog
Posts: 58
Joined: Sun May 14, 2017 6:56 pm
Location: Calgary, Alberta, Canada
Motorcycle: 1980 GL1100 Interstate

Re: front tire sizing

Post by Good Hondog » Fri May 04, 2018 9:08 pm

You're very welcome Glen. No matter what the Goldwing topic, you'll find that these guys on the GoldwingDocs forum are the best and nicest people to share advice and know-how about how to fix or service these old Honda's. Before I joined I read a lot of posts on this site after I got my 80 Interstate a couple of years ago and the collective knowledge and personal experience these great folks have convinced me this is the only place I want to be. I know my bike restoration will be a lot better because of this site and these members.

gfrench5@hotmail.com
Posts: 19
Joined: Sat Nov 25, 2017 1:41 pm
Location: Ontario
Motorcycle: 1976 Honda GL1000

Re: front tire sizing

Post by gfrench5@hotmail.com » Sat May 05, 2018 6:58 pm

Yes I agree Thanks again to all, Thanks Good Hondog , Glen



Post Reply