Torque for passenger board hex bolts

Steve L · Post by **Steve L** » Sun Nov 27, 2011 9:55 pm

Hello - I have a 2012 Goldwing, and am going to replace the stock passenger boards. Can anyone tell me what to torque the hex bolts to when I install the new boards. Even better, where can I find the torque specs for the whole bike? I also need the torque specs for the centre stand which I am going to replace. Thanks for any help.

themainviking · Post by **themainviking** » Mon Nov 28, 2011 6:19 am

I don't believe that torque is very important with the passenger floorboards. Just put some blue locktight on them and snug them up. probably 20 ft pounds is enough. They do not do anything to affect the handling or running of the motorcycle, so as long as you do not snap the bolts off it's fine. As to torque specs for the entire bike? You could get a manual for 01-10 bikes and just hope the specs are the same, but if it were me - I would wait till a manual came out for the bike you have.

upssnowman · Post by **upssnowman** » Thu Dec 01, 2011 10:00 pm

The first thing I buy with any bike is a full blown Honda repair manual
congrats on the 12

Steve L · Post by **Steve L** » Thu Dec 01, 2011 10:06 pm

Thanks - you are right about getting the manual. Only problem is that they are not yet available! I think the torque numbers that I am looking for to put on new passenger boards and centre stand will almost certainly be the same as 2010 model, so if anyone can help me with those in the interim, it would be much appreciated!

themainviking · Post by **themainviking** » Fri Dec 02, 2011 8:03 am

Steve L wrote:Thanks - you are right about getting the manual. Only problem is that they are not yet available! I think the torque numbers that I am looking for to put on new passenger boards and centre stand will almost certainly be the same as 2010 model, so if anyone can help me with those in the interim, it would be much appreciated!

Now that I can help you with. The 2009/2010 floorboard mounting bolts are 20 Ft Pounds and the left and right centerstand pivot bolts are 40 Ft pounds. And if you need it in metric, it is 27 and 54 Nms respectively.

Steve L · Post by **Steve L** » Fri Dec 02, 2011 3:33 pm

themainviking wrote:
Steve L wrote:Thanks - you are right about getting the manual. Only problem is that they are not yet available! I think the torque numbers that I am looking for to put on new passenger boards and centre stand will almost certainly be the same as 2010 model, so if anyone can help me with those in the interim, it would be much appreciated!
Now that I can help you with. The 2009/2010 floorboard mounting bolts are 20 Ft Pounds and the left and right centerstand pivot bolts are 40 Ft pounds. And if you need it in metric, it is 27 and 54 Nms respectively.

Thanks - that is exactly what I am looking for!

Len · Post by **Len** » Sat Dec 03, 2011 9:45 am

The 2012 shop manual is available from Helm, but you must call to order.
http://www.helminc.com/helm/about_conta ... Style=helm

Steve L · Post by **Steve L** » Sat Dec 03, 2011 10:13 pm

Len wrote:The 2012 shop manual is available from Helm, but you must call to order.
http://www.helminc.com/helm/about_conta ... Style=helm

Thanks, appreciate that. I was told they were not yet available. I will call them.

Torque for passenger board hex bolts

Torque for passenger board hex bolts

Re: Torque for passenger board hex bolts

Re: Torque for passenger board hex bolts

Re: Torque for passenger board hex bolts

Re: Torque for passenger board hex bolts

Re: Torque for passenger board hex bolts

Re: Torque for passenger board hex bolts

Re: Torque for passenger board hex bolts

Who is online