Macgyver Belly Pan


Reviews of Goldwing and motorcycle-related products and services
  • Sponsored Links
Post Reply
User avatar
TWOWHEELCOWBOY
Posts: 41
Joined: Thu Apr 17, 2014 8:32 am
Location: Ormond Beach, Florida
Motorcycle: 2018 Tour, DCT Air bag

Macgyver Belly Pan

Post by TWOWHEELCOWBOY » Fri Sep 01, 2017 10:34 am



Hi All, I finally bought a Macgyver Belly Pan. I hope this will help others with install. First I've read that others have had the front section Fall Off (Of course while on a Trip). So I did away with the screws it came with and used Cap Screws I also drilled and safety wired them. The screws thread into Steel spring clips which will rust over time, so I coated the threads with Never Seez. Next the hole for the hoses the hang through comes razor sharp, so I used a rubber grommet to protect the hoses. Ok on to the install, I installed the Left side as per instructions. I use a small scissor jack and a piece of wood to assist in pushing the pan up, repeated the same thing on the Right side. I can't stress enough in the importance of the small jack, without that it would be next to impossible to get it to engage safely under the cowling. In the end after looking real good with bright light and mirror, it's on, but not all the way do to the pan ends up against the Exhaust and will not go on further. Kind of makes one nervous that this could come off. Also it came with 4 scratches as other have posted, looks to me its from some kind of tool they use to hold it as the scratches were uniform. All and all it does protect the enging, oil filter, and coolest tank. But for the money they charge, it could be manufactured a lot better and safer.












[attachment=0]
Attachments






I thank Jesus for everyday I can still throw a leg over and ride :)
TWO WHEEL COWBOY

User avatar
Hoosier Jack
Posts: 393
Joined: Thu Oct 02, 2014 4:21 am
Location: Terre Haute, IN
Motorcycle: 1982 GL1100 Interstate

Re: Macgyver Belly Pan

Post by Hoosier Jack » Sat Sep 02, 2017 7:24 pm

Ok, what is a Macgyver Belly Pan?

User avatar
TWOWHEELCOWBOY
Posts: 41
Joined: Thu Apr 17, 2014 8:32 am
Location: Ormond Beach, Florida
Motorcycle: 2018 Tour, DCT Air bag

Re: Macgyver Belly Pan

Post by TWOWHEELCOWBOY » Sun Sep 03, 2017 6:57 am

Sorry I took it for granted that the readers knew. It a sheet of metal that bolts to the bottom of the engine section of a gold wing that hopefully protects the engine, oil filter, and mostly the coolant reserve tank.
Hope this helps.
I thank Jesus for everyday I can still throw a leg over and ride :)
TWO WHEEL COWBOY

User avatar
Hoosier Jack
Posts: 393
Joined: Thu Oct 02, 2014 4:21 am
Location: Terre Haute, IN
Motorcycle: 1982 GL1100 Interstate

Re: Macgyver Belly Pan

Post by Hoosier Jack » Sun Sep 03, 2017 7:38 am

It does and I figured that was the idea. Do you have a picture of installed?

User avatar
Mag
Posts: 1465
Joined: Sun Mar 25, 2012 11:58 am
Location: Silverlake, WA
Motorcycle: 1982 Yamaha Venture (Crashed/Sold)
1982 1100 Silver Goldwing (sold)
1989 1500 Beige Goldwing (sold)
1988 1500 Beige Goldwing (current ride)

Re: Macgyver Belly Pan

Post by Mag » Sun Sep 03, 2017 11:44 am

Using the diamond plate, that would look pretty cool. I would like to see, too.

User avatar
MikeB
Posts: 2063
Joined: Fri Dec 04, 2009 12:54 pm
Location: Tacoma, WA
Motorcycle: 1998 - GL1500 Aspencade.
2003 - GL1800A

Re: Macgyver Belly Pan

Post by MikeB » Sun Sep 03, 2017 1:21 pm

View the McGyver Belly Pan on YouTube by Cruiserman Garage.




Or read the Cruiserman Garage Blog.
http://blog.cruisemansgarage.com/2013/1 ... y-pan.html

Personally, I see no reason to change what I already have installed.
MikeB
Tacoma, WA, USA

harvey01
Posts: 873
Joined: Thu May 31, 2012 7:14 pm
Location: Henrico, Virginia
Motorcycle: 2004 GL1800

Re: Macgyver Belly Pan

Post by harvey01 » Mon Sep 04, 2017 11:15 am

An alternative to the MacGyver Pan is the Tulsa Belly Pan. It is made of aluminum and comes in two pieces. I have had the same one on my GL1800 for 120,000 miles with no problems. Installation was easy--loosen a couple bolts, slide the back section in place, retighten the bolts, install the front section which is held in place with two screw type fasteners. Easy on, easy off for oil changes.

See: http://www.hellotrade.com/all-american- ... y-pan.html
harvey
Ride Safe and Ride Often

User avatar
Metal Mangler
Posts: 84
Joined: Sun Sep 08, 2013 3:53 pm
Location: lyman SC
Motorcycle: 2016 Goldwing
2012 Goldwing (totaled got rear ended)
1988 Goldwing (Sold)
1980 Goldwing (Sold)

Re: Macgyver Belly Pan

Post by Metal Mangler » Thu Mar 01, 2018 6:00 am

Well that was a through review. And congrats on your safety wire job. looks like you have been around some aviation applications. I installed a belly pan from Cyclemax . I ran over a wrench a few years ago on my 2012 and punctured my filter with two holes.
Marvin (Shep) Shepard
"It´s a friggen motorcycle, it´s not supposed to be comfortable, quiet or safe. The wind noise is supposed to hurt your ears, the seat should be hard and riding it should make you s**t your pants every now and then. "

User avatar
Metal Mangler
Posts: 84
Joined: Sun Sep 08, 2013 3:53 pm
Location: lyman SC
Motorcycle: 2016 Goldwing
2012 Goldwing (totaled got rear ended)
1988 Goldwing (Sold)
1980 Goldwing (Sold)

Re: Macgyver Belly Pan

Post by Metal Mangler » Thu Mar 01, 2018 6:03 am

I installed the pan after the incident. Would probably never happen again but oh well. I also carry a spare filter.
Marvin (Shep) Shepard
"It´s a friggen motorcycle, it´s not supposed to be comfortable, quiet or safe. The wind noise is supposed to hurt your ears, the seat should be hard and riding it should make you s**t your pants every now and then. "

DaveO430
Posts: 694
Joined: Fri Jan 02, 2015 7:28 pm
Location: Amity. Ar
Motorcycle: 2010 GL1800
2004 Suzuki DR200

Re: Macgyver Belly Pan

Post by DaveO430 » Thu Mar 01, 2018 9:38 am

I have been to the McGuyver shop and watched him make one. His methods & tools are a little crude IMO but it works.

User avatar
AZgl1800
Posts: 930
Joined: Thu Oct 30, 2008 2:46 pm
Location: Lake Oologah Indian Territory USA
Motorcycle: '02 GL1800

Re: Macgyver Belly Pan

Post by AZgl1800 » Fri Mar 02, 2018 2:09 am

DaveO430 wrote:
Thu Mar 01, 2018 9:38 am
I have been to the McGuyver shop and watched him make one. His methods & tools are a little crude IMO but it works.
I have one on my 1800 and it has some scratches, from what, I don't know.
~John

See you at NASR-11 July 10th, 11th, 12th 2018

http://www.northamericangoldwings.com/c ... 9-nasr-11/

billbob
Posts: 257
Joined: Tue Jul 08, 2014 8:30 pm
Location: columbia tennessee
Motorcycle: 2005 Honda gl1800 goldwing

Re: Macgyver Belly Pan

Post by billbob » Fri Mar 02, 2018 8:02 am

I like the protection for the bottom of the bike ,oil filter and plastic tank on the bottom .



Post Reply