joecoolsuncle wrote: ↑Wed Jul 06, 2022 4:18 am saber cycle is NOT the place to buy parts. and certainly not a place to buy parts that will set you on fire.

+1

Ride to Eat – Maine, Sat. 7/9/22 Dockside Grill in Falmouth, located at Handy Boat Marina, 215 Foreside Road overlooking Casco Bay. www.thedocksidegrill.com Since there are a few folks that still have jobs, I’m shooting for Saturday, 7/9/22. Weather forecast looks acceptable. They open at 11:30 so I...

I had a Mustang on my Valkyrie and didn't care for. My friend has a Mustang on his F6B and swears by it. I have had an Ultimate on my GL1500, Valkyrie Interstate and GL1800. Very happy with all of them. There are a dozen aftermarket seat companies because we all like something different. I suggest y...

Goldwing Girl wrote: ↑Sat Jul 02, 2022 10:16 am Thank you so much. I feel like a real dope now. That is what was wrong with my volume adjustment. It’s been so long since I had a Goldwing I forgot about that setting. Thanks again. You fixed my issue.

You're welcome.

Welcome to the forum. There is a range of settings on how much the volume increases; three for speakers and two for headset. From the owner's manual: To automatically increase volume as the speed of the motorcycle increases. Push the VOLUME knob/button until ‘‘AUTO VOL SPK’’ (‘‘Auto Speaker Vol’’) i...

IIRC the GL1200 has hydraulic lash adjusters; no adjustment required or possible. I also seem to remember that the fuel pump is on the right side and makes a ticking sound just like a valve train noise.

Is it piece 2 on this diagram?
https://www.hondaparts-direct.com/oempa ... a2f1c04b/y

Take another look at the photo:

Meets ... JASO MA/MA2

New fluid can help quite a bit. The GL1500 can be difficult to properly bleed the pedal brake lines as they feed two calipers. Start with the front.

Your profile lists a 2013 F6B but you posted in the 2018+ forum. The sub harness you list is the RIVCO plug and play for 2018+ models. Correct? Is the isolator also the RIVCO unit (TWC004)? Why have you not used all the isolator connections? The RIVCO isolator instructions say: NOTE! The isolator is...

Congratulations on the new ride.

Those look like common Kuryakyn brand pegs and mounts. You could probably clamp to the vertical bar and rotate the arms around. You can check their site and see if there are different mounting blocks or arms that might work better for you.

Welcome to the forum.

There were a couple recent threads on this very subject.

Well, she’s approaching 200k miles so I keep her stabled unless the new 2012 I just put in service needs a break! I just couldn’t buy a new one at twice the cost, and the 2012 only had 4K miles on it.. Understand completely. The 2018 had just come out and I chose a 2015 with 2000 miles for half the...

Good to know. I'm going to have to do something by Thursday because the wife wants me to take her to Guthrie, OK, to see some old friends that will be in town there. I'll get over to my little hardware store in the morning before work tomorrow to get the nuts and bolts and washers and then drill aw...

At least you can do both latches for symmetry.

In your case, another location to bolt up a pair of strobes/leds. You can never have too many!

I've been thinking about this. Maybe a good place to create a mount for a dash cam?

What do you want the trailer to do for you? What are your needs and expectations? I've been through a handful, all two wheelers. To be honest, I have no complaints about any of them. Leaf springs, torsion axles, air ride, swivel hitch...at the end of the day they all go where they are towed. Don't o...

Before you drill the holes, keep in mind that they may NEVER come back in stock.

Welcome to the forum. Where are you from?

Sounds like you've already determined that you have a transmission issue. Sorry.

What I use is a reservoir-fastened RAM mount . You remove the two machine screws fastening either the left or right clutch or brake reservoir to the handlebar, and replace them with the machine screws supplied with this mount, fastening the mount in place at the same time. Then you can clamp any RA...

An ammeter certainly can be a nice piece of equipment. A direct current ammeter needs to be installed so that all current flows through it. A simplistic description is placing it in line between the battery and the battery cable. Since you want to see it from the riding position, you will need to mo...

Good question, and the search will lend you many, many results but all probably in the same vein. The reflectors are fine, and they reflect the light from the filaments of a standard H7 bulb as designed. Cheap Chinese LEDs from eBay don't put the LEDs in the same exact position as the original H7 b...

Not sure what you mean by luggage box on top of the trunk. Can you post a picture?

Most all of the large volume MC gear companies sell them. The first set I bought were Firstgear HT-Air mesh and came with a removable liner. Most brands are designed to be sold as your normal size knowing they will be overpants. Many also include some level of waist adjustment and Velcro around the ...

Andy, we live in Poland Spring. I see you are also in Maine from the photo of Height of Land. Just minutes after I posted this query I found the right deflector on the Baker Built site. I have one on order and I hope it will match. I'm two towns over. Drop me a PM or e-mail if you want to meet up f...

Hi neighbor. What part of Maine are you in? Several brand of wind deflectors look similar. National Cycle has ratchet type adjustment. The rest are strictly friction. Here are a few. Note that some of the replacement parts are interchangeable. http://bakerbuiltairwings.com/ http://motowing.com/ http...