Search found 8 matches

by ommari
Sun Oct 07, 2018 6:57 pm
Forum: GL1200 Information & Questions
Topic: Bike turns over but won't start
Replies: 2
Views: 174

Re: Bike turns over but won't start

Update: Thanks for replying jens. Late last night i began putting the bike bback together since replacing the head gasket etc. For the hell of it i turn on the ignition... Than the run switch.... I heard the pump kick in so i hit the starter... Bam ! She fired right up ? This morning She fired up..s...
by ommari
Sat Oct 06, 2018 5:09 pm
Forum: GL1200 Information & Questions
Topic: Bike turns over but won't start
Replies: 2
Views: 174

Bike turns over but won't start

Greetings wingers, It's been awhile since my last post. Let me give a small history of what was done before i ran into this problem. I stated over heating again , i did a compression check which proved to be a bad head gasket..i took the bike apart . ordered parts.. Replaced old parts with new..redo...
by ommari
Sat Jun 02, 2018 9:32 pm
Forum: GL1200 Information & Questions
Topic: Electrical troubles
Replies: 1
Views: 163

Re: Electrical troubles

Hey guys, Please ignore and dismiss this post. Gonna share a stupid moment with you guys.. After taking my ride, i failed to refuel. I did see 1 fuel bar but learned 1 fuel bar means YOUR OUT OF GAS. :o ! Filled it up this morning ( via ) gas can. She fired right up..feel stupid but still wanted to ...
by ommari
Fri Jun 01, 2018 8:07 pm
Forum: GL1200 Information & Questions
Topic: Electrical troubles
Replies: 1
Views: 163

Electrical troubles

Greeting fellow wingers. I own a 86 GL1200 sei aspencade. Yesterday 5-31, i took a 2 hour ride and all was well. Woke up this morning 6-1 and went out to fire it up turn the key and the right turn signal was flashing and i could not get it to turn off. The radio light was flashing. When i turn the s...
by ommari
Wed Dec 13, 2017 9:45 pm
Forum: GL1200 Information & Questions
Topic: Installing final drive and shaft
Replies: 2
Views: 329

Re: Installing final drive and shaft

Thanks for your reply and advice.
It seem to work just as you said it would.
Thanks man. "Topic now close" 😎
by ommari
Wed Dec 13, 2017 4:11 pm
Forum: GL1200 Information & Questions
Topic: Installing final drive and shaft
Replies: 2
Views: 329

Installing final drive and shaft

Greeting fellow winger's, Im having a major problem fitting spine to the universal. I have tried everything including. "putting bike in gear" holding in clutch and bumping it but, it still won't slide in all the way. I have tried with tire on, than only the shaft its self.can't get the bolts in flus...
by ommari
Fri Oct 16, 2015 10:16 pm
Forum: GL1200 DIY Articles
Topic: Poorboy alternator conversion on my GL1200A
Replies: 58
Views: 25615

Re: Poorboy alternator conversion on my GL1200A

Thanks for your prompt reply, i have heard what you are speaking of. But it comes on for a few seconds and.turns Off so i dont think that is my problem, I just read but confused, some say leaving the kill switch in the on position will drain the battery ? My crusie control doesnt work and the light ...
by ommari
Fri Oct 16, 2015 5:19 pm
Forum: GL1200 DIY Articles
Topic: Poorboy alternator conversion on my GL1200A
Replies: 58
Views: 25615

Re: Poorboy alternator conversion on my GL1200A

Greetings winger , I pray you all are in the best of health and riding safely. I have a starting issue concerning my poorboy conversion which was on my bike when i purchased it. Its an 86 GL1200 SEI. It ran great for a few months than something started draining my battery at start up. It will start ...