Search found 67 matches

by Peppyone1955
Thu Jul 24, 2014 7:02 pm
Forum: GL1200 Information & Questions
Topic: Breaks up..sounds like a rev limiter
Replies: 3
Views: 211

Re: Breaks up..sounds like a rev limiter

I would try a new set of spark plugs & check plug wires also. Could be a cheap fix.
by Peppyone1955
Fri Jul 11, 2014 5:57 pm
Forum: Tech Talk
Topic: THOUGHT IT WAS MY CARBS!! MAYBE NOT??? HELP
Replies: 14
Views: 610

Re: THOUGHT IT WAS MY CARBS!! MAYBE NOT??? HELP

I know this may be a dumb Question & may already been asked but have you checked to see if the fuel tank vent is open ? Could explain running ok for awhile then stalling
by Peppyone1955
Sat Apr 12, 2014 1:41 pm
Forum: Goldwing Chat
Topic: 1990 gl1500
Replies: 3
Views: 172

Re: 1990 gl1500

by Peppyone1955
Sat Oct 12, 2013 4:51 pm
Forum: Goldwing Chat
Topic: Goldwing gl1500 Inspection Sticker Plate
Replies: 3
Views: 391

Re: Goldwing gl1500 Inspection Sticker Plate

Have my State Inspection sticker mounted on the bottom of left passenger floorboard.When floorboard is down you dont see it.
by Peppyone1955
Thu Jul 11, 2013 7:47 pm
Forum: Tech Talk
Topic: oil filter
Replies: 2
Views: 242

Re: oil filter

I've been using Pureolator Pure One Filters on my 1994 aspencade for four years with no problems and Shell Rotella T 15w-40 oil. Dont want to start any arguments about Oil or Filters but just to say this is what I use and it works for me. My Two Cents!
by Peppyone1955
Mon Apr 29, 2013 4:01 pm
Forum: GL1200 Information & Questions
Topic: clutch slips
Replies: 4
Views: 226

Re: clutch slips

Oil should be fine.I would consider installing new clutch springs. Looks like DISK B, CL FRICTION 22202-ML8-600 and PLATE B, CLUTCH 22322-ML8-000 has been discontinued by Honda. Mechanic may have had to reuse these two old discs in clutch due to them being no longer availiable. You may want to check...
by Peppyone1955
Sun Apr 28, 2013 4:33 pm
Forum: GL1200 Information & Questions
Topic: clutch slips
Replies: 4
Views: 226

Re: clutch slips

When clutch was rebuilt were new clutch springs installed & what type oil are you using ?
by Peppyone1955
Wed Apr 03, 2013 4:49 pm
Forum: GL1500 Information & Questions
Topic: 1994 GL1500 SE
Replies: 6
Views: 424

Re: 1994 GL1500 SE

Just a thought but if bike has been sitting for fifteen years you might want to check & see that the exhaust has no restrictions. The little rodants like to build nests up in there on occasion. Had this happen to me one winter. Bike would start and run but didnt want to rev up properly. Cleaned out ...
by Peppyone1955
Wed Jan 30, 2013 2:45 pm
Forum: For Sale/Wanted
Topic: Looking for Riding Boot recommendations
Replies: 16
Views: 604

Re: Looking for Riding Boot recommendations

I bought 2 pair from them and was very happy with quality and price.
by Peppyone1955
Wed Jan 30, 2013 2:35 pm
Forum: For Sale/Wanted
Topic: Looking for Riding Boot recommendations
Replies: 16
Views: 604

Re: Looking for Riding Boot recommendations

Have you checked here ? May have what you are looking for.http://www.leatherup.com/c/Mens-Motorcy ... 2/119.html
by Peppyone1955
Thu Sep 27, 2012 4:27 pm
Forum: Goldwing Chat
Topic: Wind noise on intercom
Replies: 8
Views: 742

Re: Wind noise on intercom

I have the same problem with my open face helmet. I have a flat face sheild on my helmet & just tuck the mic up under the bottom of the sheild. This works good if you dont mind the flat sheild on your helmet.
by Peppyone1955
Fri Aug 31, 2012 8:17 pm
Forum: GL1100 Information & Questions
Topic: Accelerator pump linkage
Replies: 2
Views: 158

Re: Accelerator pump linkage

Accelerator Pump Adjustment on (No. 3 Carb only). The correct clearance is 0.4 in. (10mm ) which is obtained by bending the adjustment arm until the correct adjustment is obtained. Hope this helps.
by Peppyone1955
Sun Aug 12, 2012 4:34 pm
Forum: Goldwing Chat
Topic: Stock seat, jeans and sore a** = advice?
Replies: 12
Views: 395

Re: Stock seat, jeans and sore a** = advice?

Had a beaded cover for my truck seat one time & was very comfortable. Haven't tryed one of these yet!
by Peppyone1955
Sun Aug 12, 2012 4:14 pm
Forum: GL1100 Information & Questions
Topic: front brakes 81 gl1100i
Replies: 1
Views: 91

Re: front brakes 81 gl1100i

Go to GL1100 DIY articles - viewtopic.php?f=11&t=46
by Peppyone1955
Fri Aug 03, 2012 8:20 pm
Forum: Tech Talk
Topic: oil ??
Replies: 11
Views: 566

Re: oil ??

I use Shell Rotella T 15-40 in bike. When I bought bike clutch would slip on ocasion & previous owner used regular Castrol 10-40 in bike. When I switched to Rotella T problem went away after about 200 miles & clutch hasent slipped sence. I could also tell a differance in how smooth engine ran & shif...
by Peppyone1955
Sat Jun 23, 2012 9:40 pm
Forum: Goldwing Chat
Topic: cycle salvage yards in western pa
Replies: 4
Views: 1776

Re: cycle salvage yards in western pa

Don't know if any of these are close to you but here are some in Pa. I found on the net. A and J CYCLE SALVAGE - 10 Industrial Highway - Tinicum Industrial Park - Mail Stop #27 - Lester, PA 19113 Phone: 610 521-6700 ADAMS CYCLE SALVAGE and SALES - Rd. # 1 - Box 179 - Jeannette, PA 15644 Phone: 412 7...
by Peppyone1955
Sun Apr 29, 2012 12:39 pm
Forum: Tech Talk
Topic: tire age
Replies: 7
Views: 210

Re: tire age

by Peppyone1955
Sun Feb 26, 2012 1:58 pm
Forum: GL1500 Information & Questions
Topic: hazard power
Replies: 15
Views: 708

Re: hazard power

My manual shows the hazard & turn signal relay flashers are top rear, under the trunk. Good luck!
by Peppyone1955
Sat Feb 18, 2012 2:11 pm
Forum: Goldwing Chat
Topic: speaker grills
Replies: 1
Views: 138

Re: speaker grills

Don't know brand but these might work. http://www.mototourinc.com/goldwing-gl1 ... er-accents
by Peppyone1955
Wed Nov 30, 2011 5:05 pm
Forum: Goldwing Chat
Topic: Great remote garage door opener for your bike
Replies: 7
Views: 643

Re: Great remote garage door opener for your bike

This looks like the quickest way for me to get a knot put on my head or a big horse laugh from the better half for even suggesting this . I'll pass on this idea.
by Peppyone1955
Thu Nov 03, 2011 4:54 pm
Forum: GL1500 Information & Questions
Topic: Oil pump going out?
Replies: 10
Views: 691

Re: Oil pump going out?

This is a Quote from the Manuel. To remove the main oil pump and scavenging pump, perform the following: Main Oil Pump: Scavenging Pump: .. Engine removal .. Engine removal .. Engine case separation .. Clutch removal .. Rear case cover removal " Primary driven gear removal Sorry for the bad news. Go...