Search found 227 matches

by NOVAwing
Sun Sep 30, 2018 7:46 pm
Forum: GL1500 Information & Questions
Topic: fuel, ignition or worse peoblem?
Replies: 20
Views: 494

Re: fuel, ignition or worse peoblem?

Easy enough to rule out fuel. Pull the fuel line off the filter exit side and use a jumper wire from battery to the fuel pump postive point. That will make the pump run, point it into a bucket lol. If you search there is also a way to measure output volume with a measuring cup to make sure pump is n...
by NOVAwing
Sun Sep 30, 2018 7:26 pm
Forum: GL1500 Information & Questions
Topic: How to wire the Cyclemax knockout CB panel?
Replies: 3
Views: 167

Re: How to wire the Cyclemax knockout CB panel?

Thanks guys, this is what I was afraid of. For some reason I hate having to run wires aftermarket for this, yet do it all the time for car stereos lol. I guess I need to figure out how to do this. The only part I need to power right now is the dual 2.1amp usb port you see in the pics. I did not use ...
by NOVAwing
Sun Sep 30, 2018 7:10 pm
Forum: GL1500 Information & Questions
Topic: Question about legal windshields in Va
Replies: 11
Views: 275

Question about legal windshields in Va

11th hour question.... So Im about to order a new windshield. Mines all scratched up and I need a vent bad, backpressure is awful, my neck hurts lol. Is the Memphis Shades blue windshield legal in Virginia? Ive looked at the law, and lawyer blogs, and I see its not required to have one, as long as y...
by NOVAwing
Sat Sep 29, 2018 12:17 pm
Forum: GL1500 Information & Questions
Topic: How to wire the Cyclemax knockout CB panel?
Replies: 3
Views: 167

How to wire the Cyclemax knockout CB panel?

I got this because I dont have the CB. https://cyclemax.com/inc/sdetail/gl1500_cb_knockout_panel/129/14364 I assume its supposed to be plug and play? I cant see any place to plug this in. Am I missing something? Pics of the knockout panel white 2 prong plug. The 3 wire rear speaker fader harness plu...
by NOVAwing
Wed Sep 26, 2018 7:16 pm
Forum: GL1500 Information & Questions
Topic: Gas Leaking Around Gas Cap
Replies: 5
Views: 219

Re: Gas Leaking Around Gas Cap

I second the fuel petcock valve.

Parts are cheap and its easy to rebuild if your handy.
by NOVAwing
Wed Sep 26, 2018 6:57 pm
Forum: GL1500 Information & Questions
Topic: Disappointed with 96 SE, but may have a cure
Replies: 19
Views: 512

Re: Disappointed with 96 SE, but may have a cure

About 45psi in the rear shocks, set while on the centerstand, seems to be what most of us are using.

Mine stays this way at all times.

Im 250lbs + little wife 135lbs.
by NOVAwing
Mon Sep 24, 2018 7:06 pm
Forum: GL1500 Information & Questions
Topic: Disappointed with 96 SE, but may have a cure
Replies: 19
Views: 512

Re: Disappointed with 96 SE, but may have a cure

http://wingstuff.com/products/3917-superbrace-fork-brace-for-gl1500 https://www.ebay.com/p/Honda-Goldwing-GL-1500-Black-Wing-Fork-Stabilizer-Brace1988-2000-Made-USA/1839904533 this looks pretty much the same, they have to fit the same exact OEM fixture. your computer doesn't have google.com on it? ...
by NOVAwing
Fri Sep 21, 2018 5:58 pm
Forum: GL1500 Information & Questions
Topic: Another "my radio is dying" thread
Replies: 4
Views: 166

Another "my radio is dying" thread

So my radio is dying. Right after I bought new front speakers, moved the old partly blown fronts to the rear, and added the fader wiring harness for the rear. My radio mutes itself randomly, on fm which is all I use. It is not the handle bar mounted switch. If I tap, and beat hard on the main unit i...
by NOVAwing
Fri Sep 21, 2018 8:17 am
Forum: GL1500 Information & Questions
Topic: Questions about our clutch, is mine working right?
Replies: 15
Views: 889

Re: Questions about our clutch, is mine working right?

Because there's no "adjustments" for the clutch lever...if the operation seems off..do check the clutch lever pivot pin.That little part that pushes the master cylinder piston in...Seems I recall that's it's a common wear part.Either the pin outer shell is worn,the lever is worn or the contact divo...
by NOVAwing
Thu Sep 20, 2018 10:23 am
Forum: GL1500 Information & Questions
Topic: Questions about our clutch, is mine working right?
Replies: 15
Views: 889

Re: Questions about our clutch, is mine working right?

When I squeeze it, and let it out, it starts to grab about 3/4 of the way out and does not fully engage until about 90% released. Ya know...this sounds a bit far.. My88 is quite different. Mine starts to grab a bit less than half way and fully engaged at 3/4... Your pressure return port on the clut...
by NOVAwing
Thu Sep 20, 2018 10:18 am
Forum: GL1500 Information & Questions
Topic: Questions about our clutch, is mine working right?
Replies: 15
Views: 889

Re: Questions about our clutch, is mine working right?

tamathumper wrote:
Thu Sep 20, 2018 8:20 am
Check the "Clutch Lever Adjustment" section of the Owner's Manual also, to ensure you have the clutch lever travel set the way you want. It's on page 139 in my copy.
That is interesting thank you.

I will look into this for more details.

Thank you.
by NOVAwing
Thu Sep 20, 2018 10:18 am
Forum: GL1500 Information & Questions
Topic: Questions about our clutch, is mine working right?
Replies: 15
Views: 889

Re: Questions about our clutch, is mine working right?

I bought a vacuum pump at Harbor Freight for $20 and it works good for bleeding clutch and brakes. When I got my bike the PO just put brakes on it and the foot pedal had too much travel. Used the vacuum pump on it and it’s solid and high. Flushed both brake systems and the clutch in an afternoon. D...
by NOVAwing
Wed Sep 19, 2018 7:48 pm
Forum: GL1500 Information & Questions
Topic: Questions about our clutch, is mine working right?
Replies: 15
Views: 889

Re: Question about our clutch

If it just started acting different, you need to be sure the slave cylinder is not leaking. If it’s leaking, it goes into the engine and will contaminate your oil and if the engine is run too long, it will get to the bearings which is not good. Dave Thanks Rockport, It has not changed behavior sinc...
by NOVAwing
Wed Sep 19, 2018 7:14 pm
Forum: GL1500 Information & Questions
Topic: Questions about our clutch, is mine working right?
Replies: 15
Views: 889

Re: Question about our clutch

It reads as if it's normal. Is it consistant and does it feel same after holding in for a minute or two? I know you are just guess-timating travel, etc. If in doubt , it's fairly easy to bleed using squeeze & hold method with one left hand, and opening / shutting bleeder with right. Check level eve...
by NOVAwing
Wed Sep 19, 2018 6:28 pm
Forum: GL1500 Information & Questions
Topic: Mufflers for a GL1500
Replies: 2
Views: 154

Re: Mufflers for a GL1500

I don't know but I doubt it or there would be information on this site about how to do it lol.

I do know the stock mufflers are stupid expensive.

Mine look like crap but that's one part I'm not replacing until they are rotting off lol.

NOVAwing
by NOVAwing
Wed Sep 19, 2018 5:54 pm
Forum: GL1500 Information & Questions
Topic: Questions about our clutch, is mine working right?
Replies: 15
Views: 889

Questions about our clutch, is mine working right?

Hi gang, Hope everyone is well and enjoying the riding season! So about our clutch..... Hope is it supposed to work? When I squeeze it, and let it out, it starts to grab about 3/4 of the way out and does not fully engage until about 90% released. Is that normal operation or does mine need service? I...
by NOVAwing
Mon Sep 17, 2018 7:37 pm
Forum: GL1500 Information & Questions
Topic: Getting a 93 Aspencade running after 4 years sitting
Replies: 120
Views: 5186

Re: Getting a 93 Aspencade running after 4 years sitting

Update: Drink buddy is shipping. Have Showchrome knock out power panel, but decided to order the duel usb port from cyclemax instead of using the cig lighter that comes with the panel, its shipping. Truck lid cables shipping. Installed new saddlebag cables. Installed chrome faring trim both sides, t...
by NOVAwing
Mon Sep 17, 2018 7:14 pm
Forum: Goldwing Chat
Topic: Cardo Packtalk, or Sena 20s/30k
Replies: 1
Views: 75

Cardo Packtalk, or Sena 20s/30k

Sup gang, So I bought my wife a new modular helmet like mine. I already removed the old crummy built in mic hard lines on the bike. I want to be able to talk to my wife with headsets. She needs to be able to listen to her own music, and talk to me. Hopefully very simply, she is terrible with anythin...
by NOVAwing
Mon Sep 17, 2018 7:03 pm
Forum: Goldwing Chat
Topic: First time posters, say hello!
Replies: 105
Views: 3964

Re: First time posters, say hello!

Hello everyone. I forgot to do this sooner, sorry gang. Greetings from Northern Va USA. I am finishing up restoring the stock blue 93 GL1500 Aspecade I bought from my next door neighbor. He left it rotting in his backyard for 4 years with a ripped open cover. Commute to work on it weather permitting...
by NOVAwing
Sun Sep 16, 2018 9:43 am
Forum: GL1500 Information & Questions
Topic: Time for a 3D printer?
Replies: 40
Views: 1620

Re: Time for a 3D printer?

Just found this in the product review page on this site lol.

This is the shelter I bet many of us wish we had.

viewtopic.php?f=18&t=29359

NOVAwing
by NOVAwing
Sun Sep 16, 2018 8:46 am
Forum: GL1500 Information & Questions
Topic: Time for a 3D printer?
Replies: 40
Views: 1620

Re: Time for a 3D printer?

I'm wondering if this could be the switch panel you are talking about, , , , 2016 auction.jpg They're not being made anymore and are almost impossible to find. If things go well, , ,they could come back soon, so don't give up on finding/getting one. Bluthunder, Bingo! Thats the one. Yea not being m...
by NOVAwing
Thu Sep 13, 2018 10:26 am
Forum: GL1500 Information & Questions
Topic: Time for a 3D printer?
Replies: 40
Views: 1620

Re: Time for a 3D printer?

Ok guys, found pics on this thread for the aftermarket car/boat radio installations. Perhaps these mounts, or something similar can be 3d printed? I think I read you need the radio to stay intact to keep parts of the LCD dash working? So maybe we need something that mounts onto the top of the stock ...
by NOVAwing
Thu Sep 13, 2018 9:15 am
Forum: GL1500 Information & Questions
Topic: Time for a 3D printer?
Replies: 40
Views: 1620

Re: Time for a 3D printer?

For those not sure what im talking about for the switch shelter to mount extra gauges etc. See the 4th post in this thread.

viewtopic.php?f=6&t=7224

This thing is awesome and I am sure there are people that still want one? I know I do lol.

NOVAwing
by NOVAwing
Thu Sep 13, 2018 7:33 am
Forum: GL1500 Information & Questions
Topic: Time for a 3D printer?
Replies: 40
Views: 1620

Re: Time for a 3D printer?

Virgil, This is the switch cover im talking about. https://www.ebay.com/itm/1991-HONDA-GOLDWING-GL-1500-IGNITION-ELECTRICAL-COVER-WIRING-SHELTER-000579/273457932785?hash=item3fab5ce9f1:g:Xl4AAOSwantbmTWb:sc:USPSPriority!20111!US!-1&vxp=mtr Except where the wing emblem is, instead is a raised, angled...
by NOVAwing
Wed Sep 12, 2018 8:06 pm
Forum: GL1500 Information & Questions
Topic: Time for a 3D printer?
Replies: 40
Views: 1620

Re: Time for a 3D printer?

You guys with these 3d printers are awesome. Wish i had the room to get one. Any chance one of you could bring back to life that aftermarket ignition switch shelter with the hump for 2 round, (or whatever) gauges? That is something I would love to have and I would think a lot of others would to. I a...