Lost Key

[BOOK70]

I Have lost my keys to the Goldwing... and i was just woundering if someone could tell me if the locksmith could make a key from the trunk lock, or saddlebags locks, if it would work in the ignition switch, so I wouldn't have to go through the trouble of removing the switch.
My old key did work on all the locks on the bike.

Thanks TigerCop

[wingman12]

I don't see why not, if all the locks are keyed the same your locksmith should have not problem. he will probably find a code on the trunk lock to assist him. But I would call the smith of your choice to make sure before I went to pay him a visit. good luck

[BOOK70]

Thanks Wingman12...Will do

[Wilcoy02]

You can have a key sent to your home for $5.50 All you need is the key code. You can find it on any of your locks on the back side.

Here is the link to order.


http://www.ngwclub.com/catalog/index.ph ... cts_id=191

[BOOK70]

Thanks....I found itz,I think, there is 4 numbers
on the back of the lock, would that be it?

[Wilcoy02]

That would be the code he needs to make a key. It should be the same # on all the locks

[roncar]

...there is 4 numbers on the back of the lock, would that be it?

Probably, most have 5 or 6 alphanumeric digits.

In your case, (GL1200) the last 3 digits are what you're looking for. Should be A, B, C, or D followed by 2 numbers (ie C41.) That will be your key code and should be on every lock.

[Peterockwing]

Hi all, need help, I lost my key several months ago, now I broke into my filler cap to access the fuel cap. Now I cannot lock my trunk and glove box. Problem was the whole set of lock did not have same key as the ignition. I got used bike, 1 key shared between the locks except the ignition. Is it possible to get 3 locks set with 1 master key, what type of lock should I buy? Hard to get original locks. Seek your help. Thks

[DenverWinger]

Should be a 3 digit number stamped into the lock cylinders somewhere on your fuel/trunk locks. You can have a new key cut from that key code....

It's cold and snowing outside and very late, or I'd go out to the garage to see where I can find a code on my bike.

[Peterockwing]

No don't go out since it is cold. I will disconnect the barrel and have a look. Once I get the key code, where or whom should I seek to get the key cut? I m in Malaysia problem is here the the locksmith ain't that good. Perhaps u can recommend me somebody who would cut and courier or register mail to me. I would pay the person of course. Or I could pay for your trouble. So sorry to bother.

[Peterockwing]

No don't go out since it is cold. I will disconnect the barrel and have a look. Once I get the key code, where or whom should I seek to get the key cut? I m in Malaysia problem is here the the locksmith ain't that good. Perhaps u can recommend me somebody who would cut and courier or register mail to me. I would pay the person of course. Or I could pay for your trouble. So sorry to bother.

[Peterockwing]

By the way, Dennis, I broke 1 lock for the filler cap, need a new set problably better? Or use seperate key for filler if I can get the other 2 cut.
Thks again.

[offcenter]

I always keep a spare key hidden on the bike.
I know that's not helpful right now, but...just a suggestion.

[Peterockwing]

Yes that was the stupid mistake I made. Once I get all locks replaced I would probably get 3 new set of duplicates

[Rambozo]

I had this place cut a key from code for me. They were able to figure out what I had and were very helpful.
https://www.ebay.com/str/rigentinccycle
All my local locksmiths were bozos.