Austone Taxi Tire


Information and questions on GL1500 Goldwings (1988-2000)
Earl43P
Posts: 116
Joined: Sat Nov 01, 2014 7:15 pm
Location: Stafford, VA
Motorcycle: 04 ST1300 DD
99 Valkyrie IS
93 GL1500I SOLD 3/29/20
82 GL1100 SOLD 3/3/17

Re: Austone Taxi Tire

Post by Earl43P »



I'm running my second Austone Taxi Tire on my 93 GL1500I. It needs replaced, approaching the wear bars in the center tread.

My Interstate came with a single air shock. I have to keep that air shock at its maximum pressure and it does NOT bottom out with my 180 lbs. riding solo. When I say bottom out, I know that it is rubbing hard on the plastic fender liner (can see those rub marks with the tire removed).

When I add my 130 lb. wife to the back, it bottoms out much more, even on light expansion joints, like over a bridge and whatnot like pot holes and dips in the road. Very aggravating and I refuse to put up with it any longer.

For those reasons, I am going to a different car tire, likely the 195/55-16 Yoko (which I had previously run on my Valkyrie).


When all else fails, RTFM!

04 ST1300 Bought 3/4/17, Daily Driver sort of
99 Valkyrie Interstate, “Favorite”
82 GL1100 Sold 3/3/17 (miss that ticket getter)
93 GL1500I SOLD 3/29/20

User avatar
Gruntled
Posts: 10
Joined: Fri Dec 02, 2016 4:14 pm
Location: San Diego Ca
Motorcycle: 1996 Gl1500SE

Re: Austone Taxi Tire

Post by Gruntled »

Earl43P wrote:
Fri May 11, 2018 8:10 am
I'm running my second Austone Taxi Tire on my 93 GL1500I. It needs replaced, approaching the wear bars in the center tread.

My Interstate came with a single air shock. I have to keep that air shock at its maximum pressure and it does NOT bottom out with my 180 lbs. riding solo. When I say bottom out, I know that it is rubbing hard on the plastic fender liner (can see those rub marks with the tire removed).

When I add my 130 lb. wife to the back, it bottoms out much more, even on light expansion joints, like over a bridge and whatnot like pot holes and dips in the road. Very aggravating and I refuse to put up with it any longer.

For those reasons, I am going to a different car tire, likely the 195/55-16 Yoko (which I had previously run on my Valkyrie).
Earl43P wrote:
Fri May 11, 2018 8:10 am
I'm running my second Austone Taxi Tire on my 93 GL1500I. It needs replaced, approaching the wear bars in the center tread.

My Interstate came with a single air shock. I have to keep that air shock at its maximum pressure and it does NOT bottom out with my 180 lbs. riding solo. When I say bottom out, I know that it is rubbing hard on the plastic fender liner (can see those rub marks with the tire removed).

When I add my 130 lb. wife to the back, it bottoms out much more, even on light expansion joints, like over a bridge and whatnot like pot holes and dips in the road. Very aggravating and I refuse to put up with it any longer.

For those reasons, I am going to a different car tire, likely the 195/55-16 Yoko (which I had previously run on my Valkyrie).
Thanks for your feedback, it sounds like the Austone won't work for me as my wife's and my combined weight is a bit more than yours when riding double.
1996 SE

User avatar
Ravyn
Posts: 316
Joined: Wed Mar 02, 2016 11:52 pm
Location: Wa....
Motorcycle: 2002 GL1800, 2000 Kawasaki w650, 1994 Yamaha TW200, 1972 Honda ct-90 dual range tranny, 1968 Honda Express 102 original miles, 1982 Honda cx500 custom, 1972 Bultaco Alpina,
1980 Honda cx500 turbo..."SOLD" My latest bike is a 1994 GL1500SE, side car rig.

Re: Austone Taxi Tire

Post by Ravyn »

Earl43P wrote:
Fri May 11, 2018 8:10 am
I'm running my second Austone Taxi Tire on my 93 GL1500I. It needs replaced, approaching the wear bars in the center tread.

My Interstate came with a single air shock. I have to keep that air shock at its maximum pressure and it does NOT bottom out with my 180 lbs. riding solo. When I say bottom out, I know that it is rubbing hard on the plastic fender liner (can see those rub marks with the tire removed).

When I add my 130 lb. wife to the back, it bottoms out much more, even on light expansion joints, like over a bridge and whatnot like pot holes and dips in the road. Very aggravating and I refuse to put up with it any longer.

For those reasons, I am going to a different car tire, likely the 195/55-16 Yoko (which I had previously run on my Valkyrie).
Earl... you are the first one I have heard say the tire rubs when riding two up or with a heavy load. That tire is only about 1 inch taller then stock so that equates to 1/2 inch taller on either side. Are you telling us that the stock Honda tire is running that close a clearance ? I really don't think so. Maybe it is time for a suspension rebuild on your bike, it may be sagging way to much.

mikemcd
Posts: 15
Joined: Thu Aug 06, 2020 10:11 am
Location: olympia wa 98501
Motorcycle: 88 GL 1500 with trike kit.

Re: Austone Taxi Tire

Post by mikemcd »

I'm wanting to try this tire on my GL15oo trike as it's not really a motorcycle and I have a trike kit making it difficult to get at the tire. I can't seem to locate the Austone tire on any any site. Is there anyone out there that can help me with me with information about the tire or a suitable substitute? I was a Darkside rider on my 99 Interstate for a couple years. Great on the Freeway, not so great in the city. Should be excellent on a trike. I was able to lift my Valk up from being down with motorcycle tires but not so with the car tire.
Thankyou in advance for any information.

User avatar
WingAdmin
Site Admin
Posts: 21383
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (sold)
1998 XV250 Virago (sold)
2012 Suzuki Burgman 400 (wife's!)
2007 Aspen Sentry Trailer

Re: Austone Taxi Tire

Post by WingAdmin »

mikemcd wrote:
Tue Sep 01, 2020 10:01 am
I'm wanting to try this tire on my GL15oo trike as it's not really a motorcycle and I have a trike kit making it difficult to get at the tire. I can't seem to locate the Austone tire on any any site. Is there anyone out there that can help me with me with information about the tire or a suitable substitute? I was a Darkside rider on my 99 Interstate for a couple years. Great on the Freeway, not so great in the city. Should be excellent on a trike. I was able to lift my Valk up from being down with motorcycle tires but not so with the car tire.
Thankyou in advance for any information.
The Austone Taxi Tire is no longer available in the US. There is a new alternative, however: viewtopic.php?p=348530#p348530

mikemcd
Posts: 15
Joined: Thu Aug 06, 2020 10:11 am
Location: olympia wa 98501
Motorcycle: 88 GL 1500 with trike kit.

Re: Austone Taxi Tire

Post by mikemcd »

I can't thank you enough, I ordered mine. Thanks again.

User avatar
blupupher
Posts: 151
Joined: Sun May 17, 2020 5:47 pm
Location: Katy, Republic of Texas
Motorcycle: 1994 GL1500 SE

Re: Austone Taxi Tire

Post by blupupher »

mikemcd wrote:
Tue Sep 01, 2020 11:22 am
I can't thank you enough, I ordered mine. Thanks again.
Be sure to post up how it does. I have not seen any reviews of the tire yet, but it appears to be a near identical tire to the Austone.
1994 GL1500 Goldwing SE

User avatar
erkmann
Posts: 29
Joined: Wed Aug 20, 2014 10:46 pm
Location: St. Louis, MO
Motorcycle: 1999 GL1500 Aspencade
1997 GL1500 SE

Re: Austone Taxi Tire

Post by erkmann »

I'm in too, and will report back. At what pressure should I run it?

User avatar
blupupher
Posts: 151
Joined: Sun May 17, 2020 5:47 pm
Location: Katy, Republic of Texas
Motorcycle: 1994 GL1500 SE

Re: Austone Taxi Tire

Post by blupupher »

erkmann wrote:
Sun Sep 27, 2020 9:44 pm
I'm in too, and will report back. At what pressure should I run it?
Depends.
The tire you choose, how much you weigh, how much gear you pack, one up or two up, bike/suspension mods, personal preference, etc all make a difference.

Many will say set your initial pressure @ 40 psi and ride for a few hundred miles to get the tire "broken in" and get used to the different feeling with a darkside tire.
Then you start adjusting the pressure by 2 psi up or down and see how if feels compared to the 40 PSI.
Some ride as low 32 psi, some as high as 50 (never exceed the max pressure on the sidewall).

Pressure adjustment directions from the "darkside" forum:

To All:

From time to time you have heard me speak of the "sweet spot", that particular PSI that is perfect for your bike/tire/rider combination. Hopefully some of the information below will be interesting and useful to you.

Ah, the "sweet spot". "Where the heck do I find it?"

Once you put 500 miles on your new DS tire it will be broken in. Then it is time to find the "sweet spot". Find a nice 45 mph sweeping curve. Start with a tire pressure of 40#, make a couple of passes, reduce pressure 2#, make a couple of passes, reduce pressure by 2#, keep doing this until you find the special PSI that feels best on your ride, to you.

The weight of the bike, the weight of the rider, and the specific tire, all figure into what the "Sweet Spot" is for your ride.

Example: 2 LC1500's, same size riders, one bike a Goodyear Assurance Tripletread sweet spot = 32#PSI. The other a General Altimax sweet spot = 42# PSI.

So just because someone else's sweet spot is 32#, it doesn't mean that yours will be.

Later, BIGFOOT


Remember, tire pressures should be checked and adjusted with the tires cold before you start riding for the day.
1994 GL1500 Goldwing SE

User avatar
erkmann
Posts: 29
Joined: Wed Aug 20, 2014 10:46 pm
Location: St. Louis, MO
Motorcycle: 1999 GL1500 Aspencade
1997 GL1500 SE

Re: Austone Taxi Tire

Post by erkmann »

Thanks for all of that. I'm looking forward to trying it out.

Earl43P
Posts: 116
Joined: Sat Nov 01, 2014 7:15 pm
Location: Stafford, VA
Motorcycle: 04 ST1300 DD
99 Valkyrie IS
93 GL1500I SOLD 3/29/20
82 GL1100 SOLD 3/3/17

Re: Austone Taxi Tire

Post by Earl43P »

Ravyn wrote:
Fri May 11, 2018 10:05 pm
Earl43P wrote:
Fri May 11, 2018 8:10 am
I'm running my second Austone Taxi Tire on my 93 GL1500I. It needs replaced, approaching the wear bars in the center tread.

My Interstate came with a single air shock. I have to keep that air shock at its maximum pressure and it does NOT bottom out with my 180 lbs. riding solo. When I say bottom out, I know that it is rubbing hard on the plastic fender liner (can see those rub marks with the tire removed).

When I add my 130 lb. wife to the back, it bottoms out much more, even on light expansion joints, like over a bridge and whatnot like pot holes and dips in the road. Very aggravating and I refuse to put up with it any longer.

For those reasons, I am going to a different car tire, likely the 195/55-16 Yoko (which I had previously run on my Valkyrie).
Earl... you are the first one I have heard say the tire rubs when riding two up or with a heavy load. That tire is only about 1 inch taller then stock so that equates to 1/2 inch taller on either side. Are you telling us that the stock Honda tire is running that close a clearance ? I really don't think so. Maybe it is time for a suspension rebuild on your bike, it may be sagging way to much.
I sold that 93 along with a low time air shock and regular shock that I had bought but never installed (removed for a trike installation).

Hope the new owner installed those per my advice; he was bigger than I am. It’s Austin’s needed replacement. But yes the rubbing / bottoming got old quickly with my wife aboard.
When all else fails, RTFM!

04 ST1300 Bought 3/4/17, Daily Driver sort of
99 Valkyrie Interstate, “Favorite”
82 GL1100 Sold 3/3/17 (miss that ticket getter)
93 GL1500I SOLD 3/29/20

User avatar
offcenter
Posts: 719
Joined: Sat Sep 22, 2012 2:10 pm
Location: Lake Hopatcong, New Jersey
Motorcycle: 99 Gl-1500 SE
76 GL-1000
77 Honda Trail 90

Re: Austone Taxi Tire

Post by offcenter »

I run about 38 pounds of pressure in my Austone rear tire.
So far, I have around 14,000 miles on it and it is nowhere near worn out.
I love it.
I have two more in stock since they aren't for sale here anymore.
George in Jersey.
99 Goldwing GL-1500 SE
76 Goldwing Gl-1000
77 Honda CT-90 "Trail 90"

User avatar
erkmann
Posts: 29
Joined: Wed Aug 20, 2014 10:46 pm
Location: St. Louis, MO
Motorcycle: 1999 GL1500 Aspencade
1997 GL1500 SE

175R16 Maxxis Blackwall

Post by erkmann »

Regarding 'new kid on the block', the 175R16 Maxxis Blackwall from Universal Vintage Tire Company.

Initial impressions:
1. Couldn't find anyone interested in swapping out the rubber, so I spooned them on myself. 40psi was not enough to seat the bead so went well beyond that recommended max but yes, the tire eventually seated just fine
2. 3 oz beads
3. mounted to my 1999 GL1500 without difficulty
4. started at 40psi
5. no rubs
6. after first 50 miles: I was expecting a radical change in ride, but it went very smoothly. Slow speed, highway speed, no issues. I'll stick with 40psi for now, at 220 lbs and always 1-up
7. Wow. Sure is easy to get up on the center stand!
8. I'll report back after a few hundred miles

User avatar
blupupher
Posts: 151
Joined: Sun May 17, 2020 5:47 pm
Location: Katy, Republic of Texas
Motorcycle: 1994 GL1500 SE

Re: 175R16 Maxxis Blackwall

Post by blupupher »

erkmann wrote:
Mon Oct 05, 2020 9:11 pm
Regarding 'new kid on the block', the 175R16 Maxxis Blackwall from Universal Vintage Tire Company.

Initial impressions:
1. Couldn't find anyone interested in swapping out the rubber, so I spooned them on myself. 40psi was not enough to seat the bead so went well beyond that recommended max but yes, the tire eventually seated just fine
2. 3 oz beads
3. mounted to my 1999 GL1500 without difficulty
4. started at 40psi
5. no rubs
6. after first 50 miles: I was expecting a radical change in ride, but it went very smoothly. Slow speed, highway speed, no issues. I'll stick with 40psi for now, at 220 lbs and always 1-up
7. Wow. Sure is easy to get up on the center stand!
8. I'll report back after a few hundred miles
Thanks for the info. Any pics?

What tire you coming from?
1994 GL1500 Goldwing SE

User avatar
erkmann
Posts: 29
Joined: Wed Aug 20, 2014 10:46 pm
Location: St. Louis, MO
Motorcycle: 1999 GL1500 Aspencade
1997 GL1500 SE

175R16 Maxxis Blackwall

Post by erkmann »

my last tire was an Elite 4



User avatar
blupupher
Posts: 151
Joined: Sun May 17, 2020 5:47 pm
Location: Katy, Republic of Texas
Motorcycle: 1994 GL1500 SE

Re: 175R16 Maxxis Blackwall

Post by blupupher »

erkmann wrote:
Mon Oct 05, 2020 10:01 pm
my last tire was an Elite 4IMG_6639.JPG
Thanks.
I am also running an Elite 4 right now.
That tire sure does look pretty round to me.
This puts me about 90% sure I am going with the Maxxis when the time comes next year for a rear tire (I am 100% doing darkside, was wanting the Dunlop Winter Sport3D RunOnFlat, but it is not being made in the correct size any more).

Is the tire completely off the ground on the centerstand?
1994 GL1500 Goldwing SE

User avatar
erkmann
Posts: 29
Joined: Wed Aug 20, 2014 10:46 pm
Location: St. Louis, MO
Motorcycle: 1999 GL1500 Aspencade
1997 GL1500 SE

Maxxis Blackwall

Post by erkmann »

My GL1500 rear wheel with the Maxxis Blackwell touches the ground when on the center stand, cannot be rotated e.g. to find the valve stem. Did 200 miles today. Can't say I notice much difference between the Maxwell and my Elite 4 other than it just feels a little 'different'. No better, no worse, and after 200 miles I was carving through the twisties without any concerns. Whether parking lot or interstate at 80mph, the Maxxis handled very well.

User avatar
WingAdmin
Site Admin
Posts: 21383
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (sold)
1998 XV250 Virago (sold)
2012 Suzuki Burgman 400 (wife's!)
2007 Aspen Sentry Trailer

Re: Maxxis Blackwall

Post by WingAdmin »

erkmann wrote:
Tue Oct 06, 2020 7:11 pm
My GL1500 rear wheel with the Maxxis Blackwell touches the ground when on the center stand, cannot be rotated e.g. to find the valve stem. Did 200 miles today. Can't say I notice much difference between the Maxwell and my Elite 4 other than it just feels a little 'different'. No better, no worse, and after 200 miles I was carving through the twisties without any concerns. Whether parking lot or interstate at 80mph, the Maxxis handled very well.
My Austone Taxi Tire is the same - it just barely touches the ground on the center stand.

I park my bike with the center stand on a piece of 3/4" plywood, which lifts the wheel enough to let me rotate it.

User avatar
blupupher
Posts: 151
Joined: Sun May 17, 2020 5:47 pm
Location: Katy, Republic of Texas
Motorcycle: 1994 GL1500 SE

Re: Austone Taxi Tire

Post by blupupher »

OK, guess it is not a big deal that the tire still touches while on the center stand, as mentioned, I can use a piece of plywood under the center stand for maintenance when needed.


1994 GL1500 Goldwing SE

Post Reply