starter


Information and questions on GL1500 Goldwings (1988-2000)
Post Reply
User avatar
Nlmman47
Posts: 162
Joined: Thu Mar 31, 2022 8:03 am
Location: Middlesex, NC
Motorcycle: 1993 GL1500 Goldwing Aspencad

starter

Post by Nlmman47 »



have an 89 gl 1500, the starter wont engage the motor. it just spins. its probley the figers are not engaging. how do you get to unstick with the motor not turning


User avatar
offcenter
Posts: 1300
Joined: Sat Sep 22, 2012 2:10 pm
Location: Lake Hopatcong, New Jersey
Motorcycle: 99 Gl-1500 SE
76 GL-1000
77 Honda Trail 90

Re: starter

Post by offcenter »

You might need to rebuild the starter.
There are rebuild kits available, on Ebay I think.
Just be careful, there are several different starter motors on the 1500s.
Make sure you pull yours out first and compare your starter against
the pics you see on Ebay.
George in Jersey.
99 Goldwing GL-1500 SE
76 Goldwing Gl-1000
77 Honda CT-90 "Trail 90"
User avatar
WingAdmin
Site Admin
Posts: 23863
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (sold)
1998 XV250 Virago (sold)
2012 Suzuki Burgman 400 (wife's!)
2007 Aspen Sentry Trailer
Contact:

Re: starter

Post by WingAdmin »

It is going to be the starter or the sprag clutch. You won't know which until you remove the starter and try to run it out of the bike. If it still works fine, then you know it's the internal sprag clutch. If the starter doesn't turn outside of the bike, then you know it's the starter.

That said...sprag clutch failures on the 1500 are exceedingly rare. It's almost always the starter.
User avatar
Nlmman47
Posts: 162
Joined: Thu Mar 31, 2022 8:03 am
Location: Middlesex, NC
Motorcycle: 1993 GL1500 Goldwing Aspencad

Re: starter

Post by Nlmman47 »

if you pull the starter will the internals stay in place or will it fall. i had an 1100 and the sprocket inside fell down. will everything stay in place when removing the starter
User avatar
WingAdmin
Site Admin
Posts: 23863
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (sold)
1998 XV250 Virago (sold)
2012 Suzuki Burgman 400 (wife's!)
2007 Aspen Sentry Trailer
Contact:

Re: starter

Post by WingAdmin »

Nlmman47 wrote: Fri Sep 06, 2024 6:14 am if you pull the starter will the internals stay in place or will it fall. i had an 1100 and the sprocket inside fell down. will everything stay in place when removing the starter
The four-cylinder wings have the sprocket that the starter engages inside a chain. That sprocket can fall and become misaligned when the starter is pulled out, making it difficult to get the starter back in. You can mitigate that by having the bike on the side stand when you pull it.

The 1500 is a different beast - the starter also runs the reverse function, so it goes directly into a complex set of gears, with no chain involved - so you won't have the same problem.

Just be ABSOLUTELY sure that when you reinstall the starter that the spline shaft is properly aligned with the gear and the starter is fully seated against the engine before you bolt it in place. People have tried to install the starter when the spline was not aligned, leaving a little gap between the starter and the engine - which they then tried to fix by torquing down the bolts. This will BREAK the gear inside the engine, requiring you to remove the engine and split the case to repair!
User avatar
WingAdmin
Site Admin
Posts: 23863
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (sold)
1998 XV250 Virago (sold)
2012 Suzuki Burgman 400 (wife's!)
2007 Aspen Sentry Trailer
Contact:

Re: starter

Post by WingAdmin »

Did this problem just suddenly start happening?

Does it work sometimes, or it now NEVER cranks the engine?

Does the reverse still work?
User avatar
Nlmman47
Posts: 162
Joined: Thu Mar 31, 2022 8:03 am
Location: Middlesex, NC
Motorcycle: 1993 GL1500 Goldwing Aspencad

Re: starter

Post by Nlmman47 »

it just all of sudden quit spinning the engine
User avatar
gordonv
Posts: 181
Joined: Sun Oct 04, 2009 6:39 pm
Location: Richmond BC
Motorcycle: 1999 GL1500CF
1988 GL1500
1982 GL1100A

Re: starter

Post by gordonv »

First, place the transmission in gear, and bump/turn the engine over a little bit.

Try the starter. If it engages, then the teeth have broken off in the engine. If it doesn't, then most likely the starter itself. Remove starter and inspect both engine and starter. Put power to the starter and see if it spins.

Riding a Valkyrie hydro lock can be a big problem, and then you turn the engine over and it's seized and you shear the teeth off of the starter gears. Trying to find a picture/post from VRCC or my own pics.

Not the picture I wanted, but I found this link with working pic.
http://www.valkyrieforum.com/bbs/index. ... 407.0.html

You can remove the starter and with a flashlight look into the back of the engine and see that gear. Rotate it to inspect it 360'

Something wrong with the postimage.org pictures.

Found good pictures.
http://www.valkyrieforum.com/bbs/index. ... cseen.html


Post Reply