FI codes recall


Information and questions on GL1800 Goldwings (2001-2017)
Post Reply
controlu
Posts: 50
Joined: Sun Apr 21, 2019 6:40 pm
Location: S.W. Florida, U.S.A.
Motorcycle: 2003 GL1800 Goldwing / Trike Conversion

FI codes recall

Post by controlu »



Can I take my bike, '03 GL1800, to a dealer and have them pull any FI codes out of the ECM? Is there a way I can see any that have not been cleared? ( I.E. Hold the correct button while rubbing my left cheek and turning on the ignition 4 and 1/2 times)


User avatar
AZgl1800
Posts: 2652
Joined: Thu Oct 30, 2008 2:46 pm
Location: Lake Oologah Indian Territory USA
Motorcycle: '02 GL1800
2009 Piaggio MP3 250cc

Re: FI codes recall

Post by AZgl1800 »

you can do it easy.

Sidestand down, engine running, trans in Neutral.
Throttle at idle.

Leave it alone...... the FI light will being to blink a series of long and short blips.

it will repeat the sequence over and over, so that you can write it down, and verify what you saw.

2 long flashes followed by 5 short flashes equals the FI code '25'

I will post up the codes in the next post by itself for clarity
~John

'02 GL1800
2009 Piaggio MP3 250cc
User avatar
AZgl1800
Posts: 2652
Joined: Thu Oct 30, 2008 2:46 pm
Location: Lake Oologah Indian Territory USA
Motorcycle: '02 GL1800
2009 Piaggio MP3 250cc

Re: FI codes recall

Post by AZgl1800 »

FI or Fault Indicator codes

If FI (Fault Indicator) light comes on pull over but DO NOT shut bike off. Put in neutral and put side stand down, RPM’s below 1500. This signals the ECM to send the error code to the FI light. Count the number of long and short flashes. This will give you the error code. Also known as Malfunction Indicator Light (MIL)

If you shut the bike off the error code is lost - sort of. It will be retained in the ECM but it is harder to get out. If the bike stops and the will not restart you can get the FI light to flash the error code by cranking the engine for 10 seconds. The FI light will then flash the error code.

Long Blink = 10 Short Blink = 1
i.e. long long long short short short = 33 check error code 33

Number of MIL blinks .Symptoms
.Cause

0 No blinks • Engine does not start

• Open circuit in the power input and ground wires of the ECM: • Faulty bank angle sensor
• Open circuit in bank angle sensor related wires: • Faulty FI IGN relay: • Open circuit in FI IGN relay related wires
• Faulty engine stop switch: • Open circuit in engine stop switch related wires: • Faulty ECM: • Blown FI IGN fuse (20 A)
• Blown ST. KILL fuse (10 A):

0 No blinks • Engine operates normally
• Open circuit in MIL wire: • Faulty combination meter: • Faulty ECM


0 Stays lit • Engine operates normally
• Short circuit in service check connector wire: • Short circuit in MIL wire: • Faulty ECM


1 Blinks • Engine operates normally
• Loose or poorly connected MAP sensor connector: • Open or short circuit in MAP sensor wire: • Faulty MAP sensor


7 Blinks • Hard to start at a low temperature (ECM controls using preset value; coolant temperature: 85° C/185° F)
• Loose or poorly connected ECT sensor connector: • Open or short circuit in ECT sensor wire: • Faulty ECT sensor


8 Blinks • Poor engine response when operating the throttle quickly (ECM controls using preset value; throttle opening: 0° )
• Loose or poorly connected TP sensor connector: • Open or short circuit in TP sensor wire: • Faulty TP sensor


9 Blinks • Engine operates normally (ECM controls using preset value; intake air temperature: 28° C/82° F)
• Loose or poorly connected IAT sensor connector
• Open or short circuit in TP sensor wire: • Faulty IAT sensor


10 Blinks • Engine operates normally at low altitude
• Engine idles roughly at a high altitude (ECM controls using preset value; barometric pressure: 760 mm Hg/1,013 hPa)
• Loose or poorly connected BARO sensor connector: • Open or short circuit in BARO sensor wire: • Faulty BARO sensor


11 Blinks • Engine operates normally
• Loose or poorly connected vehicle speed sensor connector
• Open or short circuit in vehicle speed sensor wire: • Faulty vehicle speed sensor


12 Blinks • Engine does not start
• Loose or poorly connected No. 1 injector connector: • Open or short circuit in No. 1 injector wire: • Faulty No. 1 injector


13 Blinks • Engine does not start
• Loose or poorly connected No. 2 injector connector: • Open or short circuit in No. 2 injector wire: • Faulty No. 2 injector


14 No blinks • Engine does not start
• Loose or poorly connected No. 3 injector connector: • Open or short circuit in No. 3 injector wire: • Faulty No. 3 injector


15 Blinks • Engine does not start
• Loose or poorly connected No. 4 injector connector: • Open or short circuit in No. 4 injector wire: • Faulty No. 4 injector



16 Blinks • Engine does not start
• Loose or poorly connected No. 5 injector connector: • Open or short circuit in No. 5 injector wire: • Faulty No. 5 injector


17 Blinks • Engine does not start
• Loose or poorly connected No. 6 injector connector: • Open or short circuit in No. 6 injector wire: • Faulty No. 6 injector


18 Blinks • Engine does not start
• Loose or poorly connected camshaft position sensor connector
• Open or short circuit in camshaft position sensor wire: • Faulty camshaft position sensor


19 Blinks • Engine does not start
• Loose or poorly connected ignition pulse generator connector:
• Open or short circuit in ignition pulse generator wire: • Faulty ignition pulse generator


21 Blinks • Engine operates normally
• Open or short circuit in right O2 sensor wire: • Faulty right O2 sensor


22 Blinks • Engine operates normally
• Open or short circuit in left O2 sensor wire: • Faulty left O2 sensor


23 Blinks • Engine operates normally
• Open or short circuit in right O2 sensor heater wire: • Faulty right O2 sensor


24 Blinks • Engine operates normally
• Open or short circuit in left O2 sensor heater wire: • Faulty left O2 sensor


25 Blinks • Engine operates normally
• Loose or poorly connected right knock sensor connector: • Open or short circuit in right knock sensor wire: • Faulty right knock sensor


26 Blinks • Engine operates normally
• Loose or poorly connected left knock sensor connector: • Open or short circuit in left knock sensor wire: • Faulty left knock sensor

29 Blinks • Engine stalls, hard to start, rough idling
• Loose or poorly connected idle air control (IAC) valve connector: • Open or short circuit in IAC valve wire: • Faulty idle air control valve


33 Blinks • ECM does not hold the self diagnostic data
• Faulty E2-PROM in ECM • Engine operates normally


41 No blinks • Engine operates normally
• Loose or poorly connected connector in gear position switch related circuits
• Open or short circuit in gear position switch wires: • Faulty gear position switch: • Faulty clutch switch: • Faulty side stand switch

...................

Engine cranks but won’t start
• No fuel in tank, • No fuel to injector, – Clogged fuel filter, – Pinched or clogged fuel feed hose, – Pinched or clogged fuel tank breather tube, – Faulty fuel pump, – Faulty fuel pump circuits, • Intake air leak, • Contaminated / deteriorated fuel, • Faulty fuel injector, • Idle air control valve stuck closed, • No spark at plug Faulty ignition system

Engine stalls, hard to start, rough idling
• Restricted fuel feed hose, • Contaminated/deteriorated fuel, • Intake air leak, • Faulty idle air control valve, • Restricted fuel tank breather tube, • Misadjusted idle adjusting screw, • Faulty ignition system

Afterburn when engine braking is used
• Faulty pulse secondary air injection (PAIR) system, – Faulty PAIR control solenoid valve, – Faulty PAIR check valve, – Clogged hose of the PAIR system, • Faulty ignition system

Backfiring or misfiring during acceleration
• Faulty ignition system

Poor performance drive-ability and poor fuel economy
• Pinched or clogged fuel feed hose, • Faulty pressure regulator, • Faulty ignition system
~John

'02 GL1800
2009 Piaggio MP3 250cc
User avatar
GoldWingrGreg
Posts: 814
Joined: Tue Aug 24, 2010 7:18 am
Location: Zephyrhills, Florida
Motorcycle: 89 GL1500
03 GL1800
04 GL1800(abs)
05 GL1800(abs)
07 GL1800(abs)
Contact:

Re: FI codes recall

Post by GoldWingrGreg »

controlu wrote: Thu May 23, 2019 5:02 pm Can I take my bike, '03 GL1800, to a dealer and have them pull any FI codes out of the ECM? Is there a way I can see any that have not been cleared? ( I.E. Hold the correct button while rubbing my left cheek and turning on the ignition 4 and 1/2 times)
Yes ... to pull and/or clear the codes you will need to pull the seat. Under the seat is a connector that needs shorted. Do you have a Service Manual ???
controlu
Posts: 50
Joined: Sun Apr 21, 2019 6:40 pm
Location: S.W. Florida, U.S.A.
Motorcycle: 2003 GL1800 Goldwing / Trike Conversion

Re: FI codes recall

Post by controlu »

Yes, I have the manual and will check it out. Thank you for the response.
User avatar
GoldWingrGreg
Posts: 814
Joined: Tue Aug 24, 2010 7:18 am
Location: Zephyrhills, Florida
Motorcycle: 89 GL1500
03 GL1800
04 GL1800(abs)
05 GL1800(abs)
07 GL1800(abs)
Contact:

Re: FI codes recall

Post by GoldWingrGreg »

controlu wrote: Fri May 24, 2019 1:36 pm Yes, I have the manual and will check it out. Thank you for the response.
Go to the PGM-FI section ... it usually about 8-9 pages in
- to pull code SELF-DIAGNOSTIC DATA INDICATION PROCEDURE
- to clear code SELF-DIAGNOSTIC MEMORY RESET PROCEDURE


Post Reply