Sprag Clutch Problems


Information and questions on GL1500 Goldwings (1988-2000)
Post Reply
Signdude8771
Posts: 6
Joined: Sun Apr 28, 2019 6:30 pm
Location: Delmar, MD
Motorcycle: 1995 GL1500 SE Bike and 1998 GL1500 SE Trike

Sprag Clutch Problems

Post by Signdude8771 »



Doing a search of the forum, I'm finding a number of folks with the same problem... problems starting after the bike is warm.

The general consensus seems to be the clutch becomes clogged with gunk and crud over time.
Before having the motor removed and the clutch replaced, there seems to be another consensus,
try the Seafoam procedure first.

I notice that most of those reporting the problem seem to be '83 and '84 - 1100 and 1200 owners.

Mine being a '95 GL1500 SE, would the Seafoam method still hold true? I ask because I don't know if there is
a difference in the position and lubrication of the clutch between years.

Thanks in advance for any assistance.
Bill



User avatar
bluthundr31
Posts: 571
Joined: Tue Jul 11, 2017 11:43 pm
Location: Morgan Hill, CA.
Motorcycle: 1991 GL1500 Interstate (Cinnamon Beige)

Re: Sprag Clutch Problems

Post by bluthundr31 »

Seafoam isn't for the clutch, , , the gunked up clutch reservoir will cause "clutch slippage", , ,but clutch problems are often different than starting problems.

Are you having trouble starting after engine is warmed up? Seafoam has been used as a method to clean up low-idle jets in the carbs and will improve starting.

DaveO430
Posts: 1201
Joined: Fri Jan 02, 2015 7:28 pm
Location: Amity. Ar
Motorcycle: 2010 GL1800
2004 Suzuki DR200

Re: Sprag Clutch Problems

Post by DaveO430 »

This is the first I remember anyone ever having a starter clutch problem on a 1500. It works the same way as the 4 cyls so worth a try with seafoam.

Signdude8771
Posts: 6
Joined: Sun Apr 28, 2019 6:30 pm
Location: Delmar, MD
Motorcycle: 1995 GL1500 SE Bike and 1998 GL1500 SE Trike

Re: Sprag Clutch Problems

Post by Signdude8771 »

Thanks Guys,

Much appreciated.

User avatar
WingAdmin
Site Admin
Posts: 21492
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (sold)
1998 XV250 Virago (sold)
2012 Suzuki Burgman 400 (wife's!)
2007 Aspen Sentry Trailer

Re: Sprag Clutch Problems

Post by WingAdmin »

bluthundr31 wrote:
Tue Apr 30, 2019 12:16 am
Seafoam isn't for the clutch, , , the gunked up clutch reservoir will cause "clutch slippage", , ,but clutch problems are often different than starting problems.
In this case it is - it's for the SPRAG clutch that is part of the starter. It's a one-way clutch that lets the starter motor rotate the engine when the engine is not running, but then disconnects the starter motor as soon as the engine starts up (which is why you can press the starter button while the engine is running without doing damage - the sprag clutch won't engage).

The little sprag arms are in an area where there is not a lot of oil flowing, and as a result sludge tends to build up, and the arms stop engaging properly. Seafoam dissolves this sludge and frees up the arms.

The oil flow issue is primarily in the 4-cylinder wings, and while the GL1500 does use a sprag clutch for the starter, it is of a completely different design, in a different place.

It should be noted that if the starter is cranking the engine and it's not starting, then the problem is NOT your sprag clutch. If the starter spins freely and the engine is not cranking at all, then this is a symptom of the sprag clutch not engaging.

Signdude8771
Posts: 6
Joined: Sun Apr 28, 2019 6:30 pm
Location: Delmar, MD
Motorcycle: 1995 GL1500 SE Bike and 1998 GL1500 SE Trike

Re: Sprag Clutch Problems

Post by Signdude8771 »

That is my problem. Hit the start button and the starter motor spins at high speed, but there is no evidence the motor is turning over.
When the bike is cold, she starts instantly.

Thanks for the note.
Bill



Post Reply