Gearbrake module install 92 Aspy


Information and questions on GL1500 Goldwings (1988-2000)
  • Sponsored Links
Post Reply
ecarmichael
Posts: 30
Joined: Wed Jun 16, 2010 9:09 am
Location: Bossier City, LA
Motorcycle: 1992 GL1500 Aspencade

Gearbrake module install 92 Aspy

Post by ecarmichael » Sat Jul 07, 2018 2:40 pm



Good afternoon Sports fans!

I'm working on installing the Gearbrake flashing module on my 92 Aspencade. I've studied the schematics and have narrowed down to the 22-P WHT connector just above the air compressor. I'm planning on tapping into Brown for 12v power, Green for ground, and Green/Red for brake switch.

22-P-WHT and three isolated wires
22-P-WHT and three isolated wires

Has any of you done this mod?

I want to make sure of my logic before I start cutting wires. <br/>

Any suggestions are greatly appreciated.



User avatar
WingAdmin
Site Admin
Posts: 19421
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (wife's!)
1998 XV250 Virago (sold)
2007 Aspen Sentry Trailer

Re: Gearbrake module install 92 Aspy

Post by WingAdmin » Mon Jul 09, 2018 8:19 am

ecarmichael wrote:
Sat Jul 07, 2018 2:40 pm
Good afternoon Sports fans!

I'm working on installing the Gearbrake flashing module on my 92 Aspencade. I've studied the schematics and have narrowed down to the 22-P WHT connector just above the air compressor. I'm planning on tapping into Brown for 12v power, Green for ground, and Green/Red for brake switch.

Has any of you done this mod?

I want to make sure of my logic before I start cutting wires.

Any suggestions are greatly appreciated.
Are you looking to just have all of the brake lights flash when you apply the brakes?

ecarmichael
Posts: 30
Joined: Wed Jun 16, 2010 9:09 am
Location: Bossier City, LA
Motorcycle: 1992 GL1500 Aspencade

Re: Gearbrake module install 92 Aspy

Post by ecarmichael » Mon Jul 09, 2018 5:42 pm

Yes, that is exactly what I am trying to do.

User avatar
WingAdmin
Site Admin
Posts: 19421
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (wife's!)
1998 XV250 Virago (sold)
2007 Aspen Sentry Trailer

Re: Gearbrake module install 92 Aspy

Post by WingAdmin » Tue Jul 10, 2018 12:58 pm

ecarmichael wrote:
Mon Jul 09, 2018 5:42 pm
Yes, that is exactly what I am trying to do.
The 22 pin white connector is C10, and it is the correct one to use. Green is ground, Green/red is the brake wire you want to interrupt (+12v when brakes on), and brown has +12v when the ignition is ON. So yes, sounds like you have it exactly right.

ecarmichael
Posts: 30
Joined: Wed Jun 16, 2010 9:09 am
Location: Bossier City, LA
Motorcycle: 1992 GL1500 Aspencade

Re: Gearbrake module install 92 Aspy

Post by ecarmichael » Thu Jul 26, 2018 2:18 pm

Alrighty, post install, everything is working as advertised!!!



Post Reply