water pump replacement


Information and questions on GL1200 Goldwings (1984-1987)
  • Sponsored Links
Post Reply
bruce P
Posts: 3
Joined: Thu Dec 28, 2017 2:39 pm
Location: Montrose, Colorado
Motorcycle: 1979 1000 Goldwing. Two 1985 1200 Goldwing LTD's

water pump replacement

Post by bruce P » Sun Jul 29, 2018 11:25 pm



Has anybody had good luck with Caltric water pumps? I replaced the water pump (OEM) on my other 1200 "85 LTD several years ago and It's still going strong. I'm about to do the pump on my other LTD, due to the weep hole starting to leak a little bit. I'll probably go with another Honda OEM pump, but was just wondering if anybody has been running the Caltric after market pump with success.



User avatar
WingAdmin
Site Admin
Posts: 19546
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (wife's!)
1998 XV250 Virago (sold)
2007 Aspen Sentry Trailer

Re: water pump replacement

Post by WingAdmin » Mon Jul 30, 2018 7:03 am

bruce P wrote:
Sun Jul 29, 2018 11:25 pm
Has anybody had good luck with Caltric water pumps? I replaced the water pump (OEM) on my other 1200 "85 LTD several years ago and It's still going strong. I'm about to do the pump on my other LTD, due to the weep hole starting to leak a little bit. I'll probably go with another Honda OEM pump, but was just wondering if anybody has been running the Caltric after market pump with success.
I've heard of people asking the same question, but I don't know that I've seen anyone here posting results after having installed one. I do however know people who have installed the Saber Cycle water pump and had it fail and leak within 100 miles (or less) - and then tore things apart all over again to install an OEM pump.

Personally, the amount of my time it takes to pull the bike apart enough to get to the water pump is worth more than the $40 I would save by using an aftermarket pump, and potentially having to do it again. I would go Honda OEM.

bruce P
Posts: 3
Joined: Thu Dec 28, 2017 2:39 pm
Location: Montrose, Colorado
Motorcycle: 1979 1000 Goldwing. Two 1985 1200 Goldwing LTD's

Re: water pump replacement

Post by bruce P » Mon Jul 30, 2018 11:06 pm

Thank you WingAdmin, I'll go with the OEM pump. I do have another question: How about the K&L o-ring pump replacement kit? It seems to be the one being used even with an OEM pump. Or should I order each OEM O-ring and gasket separately?

User avatar
WingAdmin
Site Admin
Posts: 19546
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (wife's!)
1998 XV250 Virago (sold)
2007 Aspen Sentry Trailer

Re: water pump replacement

Post by WingAdmin » Tue Jul 31, 2018 10:25 am

bruce P wrote:
Mon Jul 30, 2018 11:06 pm
Thank you WingAdmin, I'll go with the OEM pump. I do have another question: How about the K&L o-ring pump replacement kit? It seems to be the one being used even with an OEM pump. Or should I order each OEM O-ring and gasket separately?
The K&L and KP Gaskets gasket and o-ring kits both seem to work very well (I used the KP Gaskets one), as does the OEM gasket kit.

The only kit that I've seen repeated complaints about is (no surprise here) the Saber Cycle kit, which has gaskets that are paper thin, and as a result cause jamming of the shift mechanism on the inside of the front engine cover.

bruce P
Posts: 3
Joined: Thu Dec 28, 2017 2:39 pm
Location: Montrose, Colorado
Motorcycle: 1979 1000 Goldwing. Two 1985 1200 Goldwing LTD's

Re: water pump replacement

Post by bruce P » Tue Jul 31, 2018 9:40 pm

Thank you, WingAdmin, I think I'll go with the K&L kit with five stars--and be really careful on what goes where. The first one I did is still working perfectly after several years. I hope I can do as well this time. I might add (as others guys have already written), that after a lifetime of working on light aircraft, where most surfaces are soft aluminum, the overall cleanup, and taking extra care that gasket surfaces are perfectly cleaned, with not even one little cross scratch from your tools, is a really big deal. Also, even though I've done this before, I'll be working with the shop manual and the how-to from this site every step of the way. Thanks again.



Post Reply