How to fix broken plastic bodywork (includes VIDEO)


Step-by-step tutorials on how to maintain and fix your GL1500
Post Reply
User avatar
WingAdmin
Site Admin
Posts: 20682
Joined: Fri Oct 03, 2008 4:16 pm
Location: Strongsville, OH
Motorcycle: 2000 GL1500 SE
1982 GL1100A Aspencade (sold)
1989 PC800 (sold)
1998 XV250 Virago (sold)
2012 Suzuki Burgman 400 (wife's!)
2007 Aspen Sentry Trailer

How to fix broken plastic bodywork (includes VIDEO)

Post by WingAdmin » Tue Dec 31, 2019 11:38 am



Our bikes are covered in plastic. It's great: it can be any shape, any color, it's light, relatively resilient, and (to a point) flexible.

However, it's also not tremendously strong, and a simple tip-over can cause cracks or breakage. As the bikes age, the plastic, exposed to heat (especially engine heat) can become brittle.

Replacing broken plastic can become expensive - it costs Honda a tremendous amount of money to store every plastic part, in every color, in the expectation that someone will need it - someday. That cost is reflected in the prices they charge.

Alternatively, eBay can be a good source of replacement body parts, as is our own Online Parts Store - we have tons of old bodywork on hand.

But what if the damage is not too severe? A crack is easily dealt with, but what about reconstructing a broken part?

In this article, we will be showing just such a reconstruction. We also have a video - if you want to skip to the video, just scroll down to the bottom of this article.

The broken piece in question is the right front brake rotor cover on my GL1500. There are two attachment points at the bottom of the rotor. Here is the good one:

Image

Here is the broken one. You can see that quite a bit of it cracked and broke away:

Image

We're going to be bonding to the ABS plastic. In order to do so, we first have to remove ALL paint, or in the case of the rotor cover, chrome plating. The easiest way to do this is with a small grinder in a Dremel tool:

Image

The chrome (or paint) on the inside needed to be removed as well.

Image

Now all the chrome plating has been removed:

Image

The tope of the piece has jagged edges that will need to be smoothed:

Image

This is fairly smooth, I didn't want to take too much plastic off.

Image

Next, we need to build up some plastic to replace what we took off (or was broken off). To do this, I use small pieces of ABS plastic. I get mine from a local injection molding factory, but you can buy a replacement ABS patch and cut it down to the size you need. It's very important to use ABS - we are going to be bonding ABS to ABS, and different plastics won't work.

Image

First, we start by heating the ABS with a heat gun. You want it warm enough to become soft, but NOT to where it starts to bubble or scorch.

Image

Start to form the soft plastic to the shape you will need. This is a trial and error process: heat, form, heat some more, form some more.

Image

Once the overall form is about right, I start to trim away the plastic to get it close to the shape I will need to add to fix the part.

Image

Trial and error again: Cut a bit, fit it, cut a bit more, fit it again.

Image

Lastly, once I'm sure I'm close, I will make the final cut to the piece, in this case using a cutting disc on a Dremel tool in order to get a nice, straight cut.

Image

The final fit:

Image

Now we start the bonding process. We will need ABS cement for this step. You can find this in the plumbing aisle of some hardware stores, or Amazon carries it as well. Do NOT use the combination PVC/ABS cement.

Image

Coat both pieces with a thin layer of ABS cement, and put the repair in place. ABS cement will actually chemically MELT the plastic pieces, so that when it cures, they become a single piece of ABS. This is why this type of repair is so far superior to other methods using glue or bonding agents. We aren't gluing pieces together, we're actually creating a new piece that is a single piece of ABS melted together.

Image

Next, we'll be making some ABS slurry. This is very soft ABS plastic that we can use as a paste. I start by using ABS drill shavings and cuttings.

Image

I put the shavings and cuttings on a piece of cardboard.

Image

Next, add some ABS glue to start melting the pieces together.

Image

MEK (available at a paint store) also works VERY well for this, and can be used to thin the slurry if it starts to thicken and cure too early.

Image

I start by smearing the semi-melted slurry around my repair.

Image

I've now coated the inside and outside of the repair in slurry, and allowed it to cure for several hours.

Image

Next, I take another piece of ABS, heat it up, and form it over top of the repair piece.

Image

Once formed, I fill it with slurry.

Image

Now I push the slurry-filled repair piece over my original repair.

Image

I repeat the process with a second piece, to give added thickness and strength to the repair.

Image

Lastly, I fill the outside well up with slurry as well. At this point, I leave the repair to sit and cure for several days. Normally, simple "use ABS cement to glue a patch over a crack" type repairs will cure to operational strength in a few hours. However, when you are working with slurry, it can take days before the solvent has fully evaporated and the piece has cured. Until then, the plastic will be very soft. The thinner the slurry, the longer it will take to cure.

Image

Once cured, I drill through the repair so the collar and screw can fit.

Image

I also use the Dremel tool to grind away the back of the repair, to make sure it is completely flat, so it fits snugly against the bracket to which it will fasten.

Image

Here is the completed repair, back on the bike. Repairs such as this normally leave the repaired part much stronger than it was originally - I don't expect I will ever have to repair this again!

Image


Here's our video demonstrating this repair:



   Never miss a video: Subscribe to the GoldwingDocs YouTube channel today!



User avatar
ctag
Posts: 17
Joined: Fri Aug 18, 2017 8:45 am
Location: Alabama, USA
Motorcycle: 1985 GL1200 Aspencade

Re: How to fix broken plastic bodywork (includes VIDEO)

Post by ctag » Sat Jan 04, 2020 12:14 pm

Thank you for the fantastic write up, WingAdmin!

Wish I'd known about this a long time ago! I've been using JB Weld's "plastic bonder" epoxy.. It works OK, but I'm definitely going to give this ABS repair a try next time!
"Voshkie" - 1985 GL1200 Aspencade

Post Reply